Fanuc Power Mate i-D/H Maintenance Manual

Index
B63175EN/03
i1
ƠSymbolsơ
MENU key, 663
[Sample setting 1] general configuration (semiclosed loop),
623
[Sample setting 2] general configuration (closed loop), 624
[Sample setting 3] tandem control configuration, 626
ƠNumbersơ
7.2inch monochrome LCD adjustment, 211
7segment LED indication, 548
7segment LED indication status change at powerup, 551
ƠAơ
AC spindle (analog interface), 392
AC spindle (serial interface), 381, 382
Action against noise, 224
Actions for trouble encountered at startup time, 640
Address, 282
Address list, 323
Adjusting reference position (dog method), 377
Adjusting the separate type PDP, 213
Adjustment of touching position, 652
Advice for use, 528
Alarm 300 (request for reference position return), 434
Alarm 401 (V ready off), 435
Alarm 404 (V ready on), 437
Alarm 417 (digital servo system is abnormal), 439
Alarm 462 (send CNC data failed), 438
Alarm 5134 (FSSB: open ready time out), 445
Alarm 5135 (FSSB: error mode), 445
Alarm 5137 (FSSB: configuration error), 445
Alarm 5139 (FSSB: error), 445
Alarm 5197 (FSSB: open time out), 445
Alarm 5198 (FSSB: ID data not read), 445
Alarm 700 (overheat at control side), 440
Alarm 704 (spindle side overheat), 441
Alarm 749 (serial spindle communication error), 442
Alarm 750 (spindle serial link cannot be started), 443
Alarm 85 to 87 (reader/puncher interface alarm), 427
Alarm 90 (reference position return is abnormal), 431
Alarm 900 (ROM parity error), 447
Alarm 910, 911 (SRAM parity error), 448
Alarm 912 to 919 (DRAM parity error), 449
Alarm 920 and 921 (watch dog or RAM parity), 449
Alarm 930 (CPU error), 450
Alarm 935 (SRAM ECC error), 451
Alarm 950 (PMC system alarm), 452
Alarm 951 (PMC watch dog alarm), 453
Alarm 972 (NMI alarm), 453
Alarm 973 (NMI alarm by unknown cause), 454
Alarm 974 (FBUS error), 455
Alarm 975 (BUS error), 456
Alarm 976 (local BUS error), 456
Alarm display, 26
Alarm history screen, 26
Alarm list, 469
Alarm screen, 608
Alarms, 636
Amplifier maintenance screen, 645
Amplifier setting screen, 642
Analog servo interface unit, 193
Associated parameters, 380
ATA card, 535
Automatic operation cannot be done, 417
Automatic setting, 621
Automatic setting of standard parameters, 391
Axis setting screen, 644
ƠBơ
Backing up a CNC data file, 609
Backpanel, 129
Backup onto the hard disk of the PC, 545
Backup using a flash memory card, 544
Base printed circuit board, 123
Basic unit of the analog servo interface unit, 146
Basic unit of the separate detector interface unit, 148
Battery, 532, 533
Battery change, 532
Battery for memory backup (3 VDC), 196
Battery life, 532
Battery replacement, 196
Block diagram, 393
Boot operation and INIT operation, 574
Boot system, 504
Boot system screen configuration and operation method, 575
Bootstrap system operation, 657
Brightness adjustment (in case of monochrome LCD), 652
Builtin debug function, 283
ƠCơ
Cable clamp and shield processing, 229
Calculation of S analog voltage and related parameters, 394
Card printed circuit board, 125
Cards that have proved to be operable on the LCD with touch
panel, 540
Clearing alarm history, 26

Leave a Reply

Your email address will not be published. Required fields are marked *