Fanuc Power Mate i-D/H Operator Manual

B–63174EN/03
C. RANGE OF COMMAND VALUE
APPENDIX
587
Increment system
IS–A IS–B IS–C
Least input increment 0.001 inch 0.0001 inch 0.00001 inch
Least command increment 0.001 inch 0.0001 inch 0.00001 inch
Max. programmable dimension ±99999.999 inch ±9999.9999 inch ±9999.9999 inch
Max. rapid traverse NOTE1 9600 inch/min 9600 inch/min 4000 inch/min
Feedrate range NOTE1 0.01 to 9600
inch/min
0.01 to 9600
inch/min
0.01 to 4000
inch/min
Incremental feed 0.001, 0.01, 0.1,
1 inch/step
0.0001, 0.001,
0.01, 0.1 inch/
step
0.00001, 0.0001,
0.001, 0.01 inch/
step
Tool compensation 0 to ±999.999
inch
0 to ±99.9999
inch
0 to ±99.99999
inch
Dwell time 0 to 999999.99
sec
0 to 99999.999
sec
0 to 9999.9999
sec
Increment system
IS–A IS–B IS–C
Least input increment 0.01 mm 0.001 mm 0.0001 mm
Least command increment 0.001 inch 0.0001 inch 0.00001 inch
Max. programmable dimension ±999999.99 mm ±99999.999 mm ±9999.9999 mm
Max. rapid traverse NOTE1 9600 inch/min 9600 inch/min 4000 inch/min
Feedrate range NOTE1 1 to 240000
mm/min
1 to 240000 mm/
min
1 to 100000
mm/min
Incremental feed 0.01, 0.1, 1,
10 mm/step
0.001, 0.01, 0.1,
1 mm/step
0.0001, 0.001,
0.01, 0.1 mm/
step
Tool compensation 0 to ±9999.99
mm
0 to ±999.999
mm
0 to ±999.9999
mm
Dwell time 0 to 999999.99
sec
0 to 99999.999
sec
0 to 9999.9999
sec
Increment system
IS–A IS–B IS–C
Least input increment 0.01 deg 0.001 deg 0.0001 deg
Least command increment 0.01 deg 0.001 deg 0.0001 deg
Max. programmable dimension ±999999.99 deg ±99999.999 deg ±9999.9999 deg
Max. rapid traverse NOTE1 240000 deg/min 240000 deg/min 100000 deg/min
Feedrate range NOTE1 1 to 240000 deg/
min
1 to 240000 deg/
min
1 to 100000 deg/
min
Incremental feed 0.01, 0.1, 1, 10
deg/step
0.001, 0.01, 0.1,
1 deg/step
0.0001, 0.001,
0.01, 0.1 deg/
step
NOTE
1 The feedrate range shown above are limitations depending
on CNC interpolation capacity. As a whole system,
limitations depending on servo system must also be
considered.
2 IS–A is available for the Power Mate i–H only.
In case of inch input,
feed screw is inch
In case of millimeter
input, feed screw is inch
Rotation axis

Leave a Reply

Your email address will not be published. Required fields are marked *