Fanuc Series 15i/150i-MA (Programming) Operators Manual

B-63324EN/03 PROGRAMMING 12.PROGRAM CONFIGURATION
- 267 -
Table12.1 (c) Major addresses and ranges of command values
Function Address Input in mm Input in inch
Program number O
*1
1 to 99999999 1 to 99999999
Sequence number N
1 to 99999999 1 to 99999999
Preparatory function G
0 to 99.9 0 to 99.9
Increment system IS-A
±
999999.99mm
±
999999.99deg.
±
99999.999inch
3
±
999999.99deg.
Increment system IS-B
±
999999.999mm
±
999999.999deg.
±
99999.9999inch
3
±
999999.999deg.
Increment system IS-C
±
99999.9999mm
±
99999.9999deg.
±
9999.99999inch
3
±
99999.9999deg.
Increment system IS-D
±
9999.99999mm
±
9999.99999deg.
±
999.999999inch
3
±
9999.99999deg.
Dimension word
Increment system
IS-E
X,Y,Z,U,V,W,A,B,
C,
I,J,K,R
*2
±
999.999999mm
±
999.999999deg.
±
99.9999999inch
3
±
999.999999deg.
Increment system IS-A
1 to 2400000mm/min 0.01 to 96000.00inch/min
Increment system IS-B
1 to 240000mm/min 0.01 to 9600.00inch/min
Increment system IS-C
1 to 100000mm/min 0.01 to 4000.00inch/min
Increment system IS-D
1 to 10000mm/min 0.01 to 400.00inch/min
Feed per minute
Increment system
IS-E
F
1 to 1000mm/min 0.01 to 40.00inch/min
Feed per revolution F
0.001 to 50000mm/rev 0.0001 to 50.0000inch/rev
Spindle speed function S
*4
0 to 4294967295 0 to 4294967295
Tool function T
*4
0 to 4294967295 0 to 4294967295
M
*4
0 to 4294967295 0 to 4294967295
Auxiliary function
B
*4
0 to 4294967295 0 to 4294967295
Offset number H, D
0 to 999 0 to 999
Increment system IS-A
0 to 999999.99 S 0 to 999999.99 S
Increment system IS-B
0 to 999999.999 S 0 to 999999.999 S
Increment system IS-C
0 to 99999.9999 S 0 to 99999.9999 S
Increment system IS-D
0 to 9999.99999 S 0 to 9999.99999 S
Dwell
Increment system
IS-E
X, P
0 to 999.999999 S 0 to 999.999999 S
Designation of a program number P
1 to 99999999 1 to 99999999
Number of subprogram repetitions L
1 to 99999999 1 to 99999999
*1 In ISO code, the colon (:) can also be used as the address of a
program number.
*2 When address I, J, K, or R is used to specify a radius for
circular interpolation, the following limitations are imposed:
Increment system Input in mm Input in inch
IS-A
±
999999999.99mm
±
99999999.999inch
IS-B
±
999999999.999mm
±
99999999.9999inch
IS-C
±
99999999.9999mm
±
9999999.99999inch
IS-D
±
9999999.99999mm
±
999999.999999inch
IS-E
±
999999.999999mm
±
99999.9999999inch

Leave a Reply

Your email address will not be published. Required fields are marked *