Fanuc Series 15i/150i-MA (Programming) Operators Manual

B-63324EN/03 INDEX
i - 3
<N>
NOMOGRAPHS ................................................................ 767
NORMAL DIRECTION CONTROL (G40.1, G41.1,
G42.1)................................................................................. 353
NOTES ON READING THIS MANUAL.......................... 7
NUMBER OF TOOL COMPENSATION SETTINGS...... 461
NURBS INTERPOLATION (G06.2)................................. 120
NURBS Interpolation Additional Functions....................... 133
<O>
OH ALARM (ALARMS RELATED TO OVERHEAT).... 814
OH ALARM (ALARMS RELATED TO OVERHEAT).... 814
OPTIONAL ANGLE CHAMFERING AND CORNER
ROUNDING....................................................................... 334
Orientation.......................................................................... 233
OT ALARM........................................................................ 808
OT ALARM........................................................................ 808
Overcutting by Cutter Compensation ................................. 426
OVERRIDE........................................................................ 159
OVERVIEW OF CUTTER COMPENSATION C (G40 -
G42).................................................................................... 378
<P>
PARALLEL AXIS CONTROL.......................................... 714
PART DRAWING AND TOOL MOVEMENT................. 15
Peck Drilling Cycle (G83).................................................. 299
Peck Rigid Tapping Cycle (G84 or G74)............................ 329
PLANE CONVERSION FUNCTION................................ 206
PLANE SELECTION......................................................... 205
POLAR COORDINATE COMMAND (G15,G16) ............ 214
POLAR COORDINATE INTERPOLATION
(G12.1,G13.1)..................................................................... 57
POSITIONING (G00) ........................................................ 40
PREPARATORY FUNCTION (G FUNCTION)............... 35
PROCESSING MACRO STATEMENTS.......................... 652
PROGRAM COMPONENTS OTHER THAN PROGRAM
SECTIONS......................................................................... 275
PROGRAM CONFIGURATION....................................... 24
PROGRAM CONFIGURATION....................................... 262
PROGRAM NUMBER ...................................................... 274
PROGRAM SECTION CONFIGURATION ..................... 264
PROGRAMMABLE MIRROR IMAGE (G50.1, G51.1)... 338
PROGRAMMABLE PARAMETER INPUT (G10)........... 561
PROGRAMMABLE SWITCHING OF
DIAMETER/RADIUS SPECIFICATION.......................... 221
PS ALARM (ALARMS RELATED TO PROGRAM)....... 785
PW ALARM (POWER MUST BE TURNED OFF THEN
ON AGAIN) ....................................................................... 810
PW ALARM (POWER MUST BE TURNED OFF THEN
ON AGAIN) ....................................................................... 810
<R>
RADIUS DIRECTION ERROR AT CIRCLE CUTTING.. 775
RANGE OF COMMAND VALUE.................................... 763
RAPID TRAVERSE........................................................... 152
Rapid Traverse Override..................................................... 160
REFERENCE POSITION .................................................. 180
Reference Position (Machine-Specific Position)................ 15
REFERENCE POSITION RETURN.................................. 181
Register, Change and Delete of Tool Life Management
Data..................................................................................... 246
REGISTERING CUSTOM MACRO PROGRAMS........... 654
Relationships with Other Functions.................................... 482
Repetition (While Statement) ............................................. 625
Retract Function ................................................................. 739
RIGID TAPPING ............................................................... 320
Rigid Tapping (G84.2)........................................................ 321
Rigid tapping Orientation Function.................................... 327
ROTARY AXIS ROLL-OVER .......................................... 719
ROTARY TABLE DYNAMIC FIXTURE OFFSET.......... 491
<S>
Sample Program.................................................................. 650
Sample Programs................................................................ 730
SCALING (G50,51)............................................................ 463
Selecting Workpiece Coordinate System(G54 to G59)....... 194
SELECTION OF TOOL USED FOR VARIOUS
MACHINING - TOOL FUNCTION .................................. 22
Setting a Workpiece Coordinate System (G92) .................. 191
Setting Workpiece Coordinate System (G54 to G59)......... 192
SIMPLE CALCULATION OF INCORRECT THREAD
LENGTH ............................................................................ 770
Simple Call (G65)............................................................... 629
SINGLE DIRECTION POSITIONING (G60) ................... 42
SKIP FUNCTION (G31).................................................... 564
SKIP FUNCTION FOR EGB AXIS(G31.8) ...................... 745
SKIPPING THE COMMANDS FOR SEVERAL AXES... 567
SMOOTH INTERPOLATION (G05.1).............................. 114
SP ALARM (ALARMS RELATED TO SPINDLE).......... 811
SP ALARM (ALARMS RELATED TO SPINDLE).......... 811

Leave a Reply

Your email address will not be published. Required fields are marked *