Fanuc Series 15i/150i-MA (Programming) Operators Manual

INDEX B-63324EN/03
i - 4
Specification Method.......................................................... 667
SPECIFYING THE SPINDLE SPEED WITH A CODE ... 224
Spindle Positioning............................................................. 232
SPINDLE POSITIONING FUNCTION............................. 230
SPINDLE SPEED FLUCTUATION DETECTION (G26,
G25).................................................................................... 236
SPINDLE SPEED FUNCTION (S FUNCTION)............... 223
SPIRAL INTERPOLATION, CONICAL
INTERPOLATION (G02,G03) .......................................... 105
SPLINE INTERPOLATION (G06.1)................................. 98
SR ALARM........................................................................ 801
SR ALARM........................................................................ 801
SUBPROGRAM (M98, M99)............................................ 270
Subprogram Call Using an M Code.................................... 645
Subprogram Call Using an M Code (Specification of
Multiple G Codes) .............................................................. 646
Subprogram Calls Using a 2nd Auxiliary Function Code... 649
Subprogram Calls Using a S Code ..................................... 648
Subprogram Calls Using a T Code ..................................... 647
SV ALARM (ALARMS RELATED TO SERVO)............. 804
SV ALARM (ALARMS RELATED TO SERVO)............. 804
SW ALARM (ALARMS RELATED TO PARAMETER
WRITING).......................................................................... 803
SW ALARM (ALARMS RELATED TO PARAMETER
WRITING).......................................................................... 803
SYNCHRONIZATION CONTROL................................... 705
Synchronization Ratio Specification Range ....................... 734
SYSTEM VARIABLES..................................................... 585
<T>
TABLE OF KANJI AND HIRAGANA CODES................ 776
TANDEM CONTROL........................................................ 706
TAPE CODE LIST............................................................. 755
Tapping Cycle (G84).......................................................... 301
THE AUXILIARY FUNCTIONS ...................................... 261
THREADING (G33)........................................................... 144
THREE-DIMENSIONAL COORDINATE
CONVERSION (G68,G69)................................................ 357
THREE-DIMENSIONAL CUTTER COMPENSATION .. 498
Three-dimensional Cutter Compensation at Tool Center
Point ................................................................................... 523
Three-dimensional rigid tapping......................................... 331
THREE-DIMENSIONAL TOOL COMPENSATION (G40,
G41).................................................................................... 452
TOOL AXIS DIRECTION TOOL LENGTH
COMPENSATION............................................................. 484
TOOL CENTER POINT CONTROL................................. 535
Tool Compensation Memory A .......................................... 460
Tool Compensation Memory B........................................... 460
Tool Compensation Memory C........................................... 460
TOOL COMPENSATION VALUES ................................. 458
Tool Data Registration, Modification, and Deletion........... 476
TOOL FIGURE AND TOOL MOTION BY PROGRAM.. 27
TOOL FUNCTION (T FUNCTION).................................. 242
Tool Length Compensation in tool axis direction with Twin
Table Control...................................................................... 702
TOOL LENGTH OFFSET (G43,G44,G49)........................ 369
Tool Life Count Restart M Code ........................................ 256
Tool Life Management Command in a Machining
Program .............................................................................. 249
Tool Life Management Data............................................... 245
TOOL LIFE MANAGEMENT FUNCTION...................... 244
TOOL MOVEMENT ALONG WORKPIECE PARTS
FIGURE-INTERPOLATION ............................................. 12
Tool Movement in Offset Mode Cancel ............................. 418
Tool Movement in Start-up................................................. 390
Tool Movement in the Offset Mode ................................... 397
TOOL MOVEMENT RANGE - STROKE......................... 28
Tool Offset Based on Tool Numbers .................................. 478
TOOL OFFSET(G45-G48)................................................. 373
TOOL OFFSETS BASED ON TOOL NUMBERS............ 475
TOOL PATH AT CORNER............................................... 772
TOOL SELECTION FUNCTION ...................................... 243
Tool Service Life Count and Tool Selection....................... 254
Tool Side Compensation..................................................... 499
TOOL WITHDRAWAL AND RETURN (G10.6).............. 747
TORQUE LIMIT SKIP ...................................................... 575
TWIN TABLE CONTROL................................................. 698
<U>
Unconditional Branch (GOTO Statement).......................... 622
<V>
VARIABLES...................................................................... 580
Vector Holding (G38)......................................................... 447
<W>
WORKPIECE COORDINATE SYSTEM.......................... 190
Workpiece Coordinate System Preset (G92.1) ................... 200
WRITE-PROTECTING COMMON VARIABLES ........... 657

Leave a Reply

Your email address will not be published. Required fields are marked *