FANUC Series 16/18/160/180-Model C for Lathe Operator Manual

INDEX
B–62754EN/01
i–7
Setting the floating reference position, 642
Setting the forbidden area for the two–path control, 537
Setting the tape, 778
Setting the workpiece coordinate system shifting amount, 681
Simple calculation of incorrect thread length, 746
Simple call (G65), 296
Simple synchronization control, 350
Single block, 502, 527
Skip function (G31), 70
Slot status display, 467
Soft key transition triggered by the function key
GRAPH
, 457
Soft key transition triggered by the function key
HELP
, 456
Soft key transition triggered by the function key
MESSAGE
, 456
Soft key transition triggered by the function key
OFFSET
SETTING
, 452
Soft key transition triggered by the function key
POS
, 443
Soft key transition triggered by the function key
PROG
(when the
soft key [BG–EDT] is pressed in all modes), 450
Soft key transition triggered by the function key
PROG
in the EDIT
mode, 446
Soft key transition triggered by the function key
PROG
in the
HNDL, JOG, or REF mode, 449
Soft key transition triggered by the function key
PROG
in the MDI
mode, 448
Soft key transition triggered by the function key
PROG
in the MEM
mode, 444
Soft key transition triggered by the function key
PROG
in the TJOG
or THDL mode, 449
Soft key transition triggered by the function key
SYSTEM
, 454
Soft keys, 440, 442
Specification method, 317
Specifying a tool group in a machining program, 122
Specifying no file number, 507
Specifying the spindle speed value directly, 106
Specifying the spindle speed with a code, 106
Spindle control in two–path control, 386
Spindle orientation, 113
Spindle positioning, 113
Spindle positioning function, 113
Spindle speed fluctuation detection function (G25, G26), 110
Spindle speed function, 105
Stamping the machining time, 653
State in which an auxiliary function is being executed, 709
Status when turning power on, when clear and when reset, 752
Stock removal in facing (G72), 160
Stock removal in turning (G71), 156
Stopping and terminating memory operation, 490
Stopping MDI operation, 493
Stopping memory operation, 489
Stopping the punch, 565
Stroke check, 534
Stroke limit check prior to performing movement, 545
Subprogram, 139
Subprogram call function (M198), 509
Subprogram call using an M code, 304
Subprogram calling, 331
Subprogram calls using a T code, 305
Subprogram nesting, 494
Supplementary explanation for copying, moving and merging, 603
Synchronization control, 352
Synchronization control and composite control, 388
System screen, 454, 628
System variables, 279
Ơ
T
ơ
T code for tool offset, 203
Tailstock barrier setting screen, 539
Tape code list, 735
Terminating MDI operation, 493
Terminating memory operation, 490
Test operation, 521
Testing a program, 411
THD, 476
The center of the arc is identical with the start position or the end
position, 233
The next block to G31 is an absolute command for 1 axis, 71
The next block to G31 is an incremental command, 71
The second auxiliary functions (B codes), 127
There is no inner intersection, 233
Thread cutting cycle (G92), 148
Timing for displaying an alarm, 537
Tool compensation and number of tool compensation, 265
Tool compensation values, number of compensation value, and
entering values from the program (G10), 265
Tool figure and tool motion by program, 29
Tool function (T function), 116
Tool geometry offset, 202
Tool life management, 118
Tool movement along workpiece parts figure–interpolation, 12
Tool movement by programing – automatic operation, 408
Tool movement in offset mode, 228

Leave a Reply

Your email address will not be published. Required fields are marked *