FANUC Series 16/18/160/180-Model C Machining Center Operators Manual

Index
B–62764EN/01
i–1
Ơ
Numbers
ơ
14 color CRT/LMDI (Vertical type), 516
14 color CRT/MDI (horizontal type), 515
14CRT and 9.5LCD soft key configuration, 545
2nd, 3rd, and 4th reference position return (G30), 105
7.2 monochrome LCD (separate type), 518
8.4 color LCD (separate type), 518
8.4 color LCD/MDI (small type, sheet key), 512
8.4 color LCD/MDI (standard type, sheet key), 513
8–digit program number, 170
9.5 color LCD/MDI (horizontal type), 513
9.5 color LCD (separate type), 519
9.5 color LCD/MDI (Vertical type), 514
9 monochrome CRT (Separate Type), 517
9 monochrome CRT/MDI (small type), 511
9 monochrome CRT/MDI (standard type), 511
9 monochrome PDP (separate type), 517
9 monochrome PDP/MDI (standard type), 512
Ơ
A
ơ
A block without tool movement, 305
A block without tool movement specified at start–up, 293
A block without tool movement specified in offset mode, 305
A block without tool movement specified together with offset
cancel, 311
Abbreviations of arithmetic and logic operation commands, 383
Abbreviations of custom macro word, 712
About this manual, 3
Absolute and incremental programming (G90, G91), 125
Absolute and relative position display, 467
Absolute coordinates, 19
Absolute position display, 246
Acceleration/deceleration type, 445
Acceleration/deceleration before interpolation, 96, 99
Acceleration/deceleration for rapid traverse, 558
Actual feedrate display, 743
Actual feedrate display of rotary axis, 744
Actual feedrate display on the other screen, 744
Actual feedrate value, 743
Adding workpiece coordinate systems (G54.1 or G54), 119
Addition and change of tool life management data, 143, 144
Address for the canned cycle repetition count, 436
Address for the cutter compensation offset number, 436
Alarm, 602, 607, 761
Alarm and self–diagnosis functions, 653
Alarm detail screen, 846
Alarm display, 506, 654
Alarm during three–dimensional tool compensation, 344
Alarm history display, 656
Alarm issued at startup, 344
Alarm list, 882
Alarm screen, 654
Alarm status, 808
Alarms during background editing, 713
Altering a word, 694
An alarm while a program is output, 669
Angle, 825
Angle between two blocks, 96
Angle for which figure insertion is ignored, 362
Angle of the C axis, 360
Angle units, 382
Angular axis control/angular axis control B, 466
Angular displacement R, 245
ANIM.SPEED, 838
Another method for alarm displays, 654
Automatic operation, 583
Arc radius specification in the cylindrical interpolation mode,
55
Argument specification, 393, 399, 400, 401
Arithmetic and logic operation, 382
ATAN function, 382
Automatic acceleration/deceleration, 81
Automatic corner deceleration, 95
Automatic erase CRT screen display, 812
Automatic grinding wheel diameter compensation after dress-
ing, 229
Automatic insertion of sequence numbers, 718
Automatic operation, 497
Automatic operation control, 377
Automatic operation status, 807
Automatic override for inner corners, 89
Automatic override for inner corners (G62), 91
Automatic reference position return, 459
Automatic reference position return check, 459
Automatic scaling, 820
Automatic tool length measurement (G37), 261
Auxiliary function, 150, 628
Auxiliary function (M function), 151
Auxiliary function lock, 500, 636
Available functions, 441
Axes, 824
Axes that are not considered part of a polar coordinate com-
mand in the polar coordinate mode, 128
Axis configuration, 569, 572
Axis control functions, 457
Axis moving status/dwell status, 807
Axis name, 29
Axis No. (P_), 434
Axis selection, 620

Leave a Reply

Your email address will not be published. Required fields are marked *