FANUC Series 16/18/160/180-Model C Machining Center Operators Manual

INDEX
B–62764EN/01
i–11
Rigid tapping, 209
Rigid tapping (G84), 210
Rotary axis roll–over, 461
Rotation, 825
Rotational copy, 235, 238
Rotational copy (spot boring), 239
ROUND function, 382
Rounding up and down to an integer, 383
Run time, 745
Run time and part count settings, 782
Ơ
S
ơ
S5–Digit command, 132
Safety functions, 643
Scale, 826
Scaling (G50, G51), 348
Scaling and coordinate system rotation, 356
Scaling of circular interpolation, 350
Scaling of each axis, programmable mirror image (negative
magnification), 349
Scaling up or down along all axes at the same rate of magnifica-
tion, 349
Scheduling function, 603
Scheduling function for the 16–TTA and 18–TTA, 607
Screen displayed at power–on, 552
Screen fields and their meanings, 682
Screen indicating module setting status, 553
Screen transition chart, 727
Screen transition triggered by the function key
OFFSET
SETTING
, 731
Screen transition triggered by the function key
POS
, 728
Screen transition triggered by the function key
PROG
in the
EDIT mode, 730
Screen transition triggered by the function key
PROG
in the
MEMORY or MDI mode, 729
Screen transition triggered by the function key
SYSTEM
, 732
Screens displayed by function key (In memory mode or MDI
mode), 749
Screens displayed by function key
OFFSET
SETTING
, 771
Screens displayed by function key
POS
, 734
Screens displayed by function key
PROG
(in the edit mode),
765
Screens displayed by function key
SYSTEM
, 801, 809
Screens on which jog feed is valid, 790
Searching in sub–program, 700
Selected plane, 97
Selecting a machine coordinate system (G35), 111
Selecting a workpiece coordinate system, 113
Selecting offset space, 342
Selecting the additional workpiece coordinate systems, 119
Selection of the offset plane, 271, 284
Separate type MDI (Horizontal type) for 9.5 LCD, 522
Separate type MDI (small key) for 9 CRT/PDP, 8.4/7.2 LCD,
519
Separate type MDI (Standard key) for 9 CRT/PDP, 8.4/7.2
LCD, 520
Separate type MDI (vertical type) for 9.5 LCD, 521
Sequence number after the program is executed, 780
Sequence number and block, 161
Sequence number comparison and stop, 779
Sequence number search, 699
Sequence stop, 778
Setting 0 in parameter PASSWD, 715
Setting a tool life cout type for groups, 145
Setting a workpiece, 112
Setting an editing range, 708
Setting and display units, 510
Setting and displaying data, 727
Setting and displaying the tool offset value, 772
Setting basic axes and rotary axes, 571, 575
Setting data, 803
Setting of the reference position return feedrate, 105
Setting parameter PASSWD, 714
Setting parameters with external input/output devices, 803
Setting screens, 733
Setting the allowable feedrate difference along each axis, 100
Setting the center coordinate of the graphics range and graphics
magnification, 816
Setting the current position as the origin of the polar coordinate
system, 127
Setting the floating reference position, 746
Setting the graphics range, 815
Setting the maximum and minimum coordinates for the drawing
range in the program, 817
Setting the relative coordinates, 739
Setting the tape, 905
Setting the workpiece coordinate system, 261
Setting the workpiece coordinate system for constant surface
speed control, 134
Setting the workpiece zero point offset value in the additional
workpiece coordinate systems, 119
Setting the zero point of the workpiece coordinate system as the
origin of the polar coordinate system, 126
Side view selection in triplane drawing, 840
Signal indicating that the cycle is in progress, 191

Leave a Reply

Your email address will not be published. Required fields are marked *