FANUC Series 16/18/160/180-Model C Machining Center Operators Manual

INDEX
B–62764EN/01
i–12
Significant digits, 686
Simple calculation of incorrect thread length, 873
Simple call (G65), 393
Simple electric gear box (G80, G81), 474
Simple synchronous control, 458
Simultaneous input/output, 594
Single block, 193, 500, 602, 620, 629, 641
Single block during a canned cycle, 642
Single direction positioning (G60), 41
Skip function (G31), 75
Skip function (G31), automatic tool length measurement (G37),
627
Smooth interpolation (G05.1), 67
Soft key functions on the “PATH GRAPHIC [EXECU-
TION]”screen, 827
Soft key functions on the “solid graphic (Execution)” screen,
838
Soft key transition triggered by the function key
GRAPH
, 542
Soft key transition triggered by the function key
HELP
, 541
Soft key transition triggered by the function key
MESSAGE
, 541
Soft key transition triggered by the function key
OFFSET
SETTING
, 537
Soft key transition triggered by the function key
PROG
(when
the soft key [BG–EDT] is pressed in all modes), 535
Soft key transition triggered by the function key
PROG
in the
EDIT mode, 531
Soft key transition triggered by the function key
PROG
in the
HNDL, JOG, or REF mode, 534
Soft key transition triggered by the function key
PROG
in the
MDI mode, 533
Soft key transition triggered by the function key
PROG
in the
MEM mode, 529
Soft key transition triggered by the function key
PROG
in the
TJOG or THDL mode, 534
Soft key transtation triggered by the function key
POS
, 528
Soft key transition triggered by the function key
SYSTEM
, 539
Soft keys, 527
Soft status display, 552
Solid graphic (BLANK), 830
Solid graphics, 829
Solid graphics (EXECUTION), 831
Solid model graphic, 829
Specifiable G codes, 61
Specification of the tool length offset value, 254
Specifying a radius in the polar coordinate mode, 128
Specifying address, 236
Specifying address I, 193
Specifying angles and a radius with absolute commands, 127
Specifying angles with incremental commands and a radius
with absolute commands, 127
Specifying G28 (automatic return to the reference position) in
the offset mode, 303
Specifying G29 (automatic return from the reference position)
in the offset mode, 303
Specifying G37, 261
Specifying I, J, and K, 344
Specifying no file number, 606
Specifying P codes, 120
Specifying the blank form and tool form in the part program,
839
Specifying the center of rotation, 236
Specifying the second conversion, 245
Specifying the sequence number for the return destination in the
main program, 168
Specifying the slave axis, 459
Specifying the spindle speed value directly, 132
Specifying the spindle speed with a code, 132
Speedometer, 748
Spindle speed function, 131
Stamping the machining time, 757, 761
Start and stop, 497
Start point and end point, 59
Start seq. No. and end seq. No., 826, 838
Start up, 284
Start up (cutter compensation start), 271
Start up (starting three–dimensional tool compensation), 342
Start up (tool compensation start), 284
Starting compensation and cutting along the Z–axis, 320
State in which an auxiliary function is being executed, 808
Status when turning power on, when clear and when reset, 879
Stop in the canned cycle, 780
Stopping and terminating memory operation, 585
Stopping MDI operation, 588
Stopping memory operation, 584
Stopping retraction, 619
Stopping the punch, 669
Stored stroke check function on/off (G22,G23), 626
Stroke check, 646
Stroke limit check prior to performing movement, 650
Subprogram, 166
Subprogram call, 166, 436
Subprogram call and single block, 642
Subprogram call function, 608

Leave a Reply

Your email address will not be published. Required fields are marked *