Fanuc Symbol CAPi T Operators Manual

Index
B–63304EN/02
i–1
ƠAơ
Additional parameter of submemory, 217
Ani, 798
Animated simulation, 516, 713
Animated simulation (menu 6), 578
Animated simulation (menu no. 6), 797
Animated simulation for two–path lathe, 703
Animated simulation founction, 760
Animated simulation founction B, 711
Animated simulation function (menu 6), 446
Animated simulation of slanted surface machining at NC data
creation, 796
Animated simulation of turning, 698
Animated simulation screens, 697
Animated simulation with gradation, 699
Animation drawing (menu No.6), 613
Applicable CNC, 767
Application for NC chaser lathe, 331
Approach and relief to inner diameter, 339
Approach, escape, and movement between slanted surface
machining figures, 785
Area division, 644
Auto collision avoidance function (15–TTFB only), 202
Automatic process determination for a closed figure, 661
Automatic process specification for 5700 series, 947
Automatic processing decision, 679
Automatic processing decision function, 677
Automatic selection of a tool, 636
Auxiliary commands, 732
Availability, 712
ƠBơ
Balance cut FAPT function (2–path lathe only), 191
Balance cutting process, 193
Bar feed, 934
Batch input functions for chamfering and corner R, 61
Blank and drawing (drawing and blank), 33
Blank and part (part figure), 38
Blank figure in grooving area, 392
Blank figure input of special figure blank, 57
Blind hole and through hole, 445, 946
ƠCơ
C–axis animated simulation, 700
C–axis FAPT animated screen, 448
C–axis FAPT function B, 502
C–axis machining with a machining plane specified, 426
CAP II for two–path lathe with two opposing spindles, 743
Cautions for using Symbolic FAPT, 360
Cautions for using the 2–path lathe mode, 404
Cautions on C–axis FAPT, 488
Center drilling and bar feeding, 647
Changing the number of registered tools, 305
Check screen, 345
Checking NC data (animated simulation function), 160
Checking slanted surface machining figures, 778
Chucking position, 402
Closed part, 390
Collation and input/output with floppy cassette, 227
Coloring data input/output, 730
Coloring data setting, 725
Coloring data setting initialization, 731
Coloring data setting screen, 728
Compatibility with CAP II, 734
Concaved parts in groove, 393
Constant surface speed control for balance cut B, 200
Conversational automatic programming function, 5
Conversion of input unit (mm/inch), 299
Creating NC data (menu no. 5), 789
Cut off machining, 930
Cut off machining, bar feed, 930
Cutting area, 559
Cutting area definitions, 927
Cutting area screen, 676
Cutting condition screen, 676
Cutting conditions, 109, 433, 560, 918
Cutting direction, 642, 917
Cutting direction and cutting edge angle, 367
Cutting overhung portion, 397
Cutting start position and others, 402
ƠDơ
Defining a new process, 628
Defining machining (menu 4), 554
Defining part figures (menu no. 2), 774
Defining slanted surface machining, 781
Defining slanted surface machining figures, 775
Definition by manual, 674
Definition of “sub cycle” process in definition of machining,
180
Definition of blank figure, 669, 745
Definition of optional blank figure, 390
Definition of part figure, 670, 745
Depth of cut (D) in drilling, 394
Depth of screw thread, 396
Description of operations, 723
Designation method, 314
Designation of C–axis figure data, 410

Leave a Reply

Your email address will not be published. Required fields are marked *