1. Fanuc
  2. Spindle Amplifier

Spindle Amplifier Additional Manual Page 3

Additional Manual
3/7
Design.
Date Ed.
A
u
g
./25/05
S
HEET
DRAW. No.
C
U
S
T.
TITLE
M. Niwa
Newly
Spindle Amplifier αi series
Backlash Acceleration Description
A
-53866E-0468
FANUC LTD
01
4. Related parameters
4.1. List of related parameters
Parameter No.
15i 16i 30i
Description
3402#0 4402#0 4402#0
Function bit of Spindle Backlash Acceleration
3402#1 4402#1 4402#1
Setting of feedforward coefficient at backlash acceleration
3455 4455 4455
Amount of backlash acceleration
3456 4456 4456
Stop timing of backlash acceleration
4.2. Details of related parameters
15i 16i 30i #7 #6 #5 #4 #3 #2 #1 #0
3402 4402 4402
MDLINF BKAFNC
SPDTDM Function bit of Spindle Backlash Acceleration
0 : Spindle backlash acceleration is unavailable
1 : Spindle backlash acceleration is available
MDLINF Setting of feedforward coefficient at backlash acceleration
Set “0” when feedforward coefficient is not 100% (P4344≠10000).
Set “1” when feedforward coefficient is 100% (P4344=10000).
15i 16i 30i
3455 4455 4455
Amount of backlash acceleration
data unit :
data range : 0 to 32767
standard setting : 0
Sets amount of backlash acceleration.
15i 16i 30i
3456 4456 4456
Stop timing of backlash acceleration
data unit : 0.001deg
data range : 0 to 32767
standard setting : 0
Sets stop timing of backlash acceleration.
Previous page
Next page

Contents Summary of Spindle Amplifier Additional Manual

  • Page 1Spindle Amplifier αi series Backlash Acceleration Description 1. General .............................................................................................................................................. 2 1.1. Overview ....................................................................
  • Page 21. General 1.1. Overview This manual describes how to use Spindle Backlash Acceleration function. 1.2. Remarks ・ This function is valid in advanced feedforward of Cs contouring control mode. ・ Following functions cannot be used with this function simultaneously (1) Sub-spindle of Spindle switching c
  • Page 34. Related parameters 4.1. List of related parameters Parameter No. Description 15i 16i 30i 3402#0 4402#0 4402#0 Function bit of Spindle Backlash Acceleration 3402#1 4402#1 4402#1 Setting of feedforward coefficient at backlash acceleration 3455 4455 4455 Amount of backlash acceleration 3456 4456 445
  • Page 45. Tuning example 5.1. CNC Program Prepare following program that draw arc (eccentric circle) in polar coordinate interpolation. Imaginary C-axis 15mm 20mm C-axis move area Center of circle (35, 0) Radius of circle 20mm X-axis Origin of workpiece Start point (15, 0) coordinate system 1 G90 ← Absolut
  • Page 55.2. Preparation of data measurement by SERVO GUIDE Open graph window of SERVO GUIDE, and execute channel setting as follows. Set distance between start point and origin. 2 2 √15 +0 = 15 (mm) Set angle of start point. -1 tan (0/15) = 0 (deg) TITLE Spindle Amplifier αi series Backlash Acceleration De
  • Page 65.3. Data measurement and display by SERVO GUIDE Execute CNC program described previously, and press button during dwell for origin operation. Then press button for starting measurement. Change graph mode of SERVO GUIDE and display circle after measurement. XTYT mode NORMAL mode Change mode from men
  • Page 75.4. Tuning Viewing arc figure in CIRCLE mode of graph window, tune parameters as follows. (a) Set following initial values. Amount of backlash acceleration (No.4455) : 5 Stop timing of backlash acceleration (No.4456) :100 (b) Raise Amount of backlash acceleration (No.4455) until peak value of quadr