FANUC Series 30i/300i/300is/31i/310i/310is/32i/320i/320is-MODEL A Additional Manual Page 1

Additional Manual
EDIT.
FANUC LTD
SHEET
DRAW. NO.
CUST.
TITLE
DESCRIPTIONDESIG.DATE
FANUC Series 30i/300i/300is/31i/310i/310is/
32i/320i/320is-MODEL A
A
nalog spindle connection material
A
-65557EN/01
The connection of analog spindle
When analog spindle is used, the servo card D11,D12 or D24 is required. These
servo cards have analog spindle function. The connectors for analog spindle
function are on the CNC main board.
Connection diagram
The maximum number of axes for each FSSB line depend on the control method
of the line. See the table below.
<SERVO CARD D11>
Control method and
maximum number of
axes
HRV2 HRV3 HRV4
Connector
name
Remarks
First FSSB line 4 axes 3 axes 1 axes COP10A-1 On the servo card
Second FSSB line 0 axes 0 axes 0 axes COP10A-2 Not mounted
Third FSSB line 8 axes 10 xes 4 axes COP10A-3 On the additional axis board
<SERVO CARD D12>
Control method and
maximum number of
axes
HRV2 HRV3 HRV4
Connector
name
Remarks
First FSSB line 8 axes 6 axes 2 axes COP10A-1 On the servo card
Second FSSB line 0 axes 0 axes 0 axes COP10A-2 Not mounted
Third FSSB line 8 axes 10 xes 4 axes COP10A-3 On the additional axis board
MAIN BOARD
A-OUT & HDI(JA40)
SPDL & POS(JA41)
Servo card with analog spindle
function
FSSB(COP10A-1)
FSSB(COP10A-2)
A
nalog spindle output
High-speed skip input
Position coder
Servo amplifiers or separate
detector interface unit
01 04.12.01 Komaki First issue Aoyama
1/5
02 05.06.24 Komaki P3 ,5 is modified.

Contents Summary of FANUC Series 30i/300i/300is/31i/310i/310is/32i/320i/320is-MODEL A Additional Manual

  • Page 1The connection of analog spindle When analog spindle is used, the servo card D11,D12 or D24 is required. These servo cards have analog spindle function. The connectors for analog spindle function are on the CNC main board. Connection diagram MAIN BOARD Analog spindle output A-OUT & HDI(JA40) High-sp
  • Page 2 Control method and Connector Remarks maximum number of name axes HRV2 HRV3 HRV4 First FSSB line 16axes 10axes 4 axes COP10A-1 On the servo card Second FSSB line 0 axes 2 axes 0 axes COP10A-2 On the servo card Third FSSB line 8 axes 10 xes 4 axes COP10A-3 On the additional axis board
  • Page 3( ) ( ) 0V 0V ( ) ( ) 0V 0V ( ) ( ) 0V ( ) 0V ( ) 0V 0V NOTE 1. When signals ENB1 and 2 turn off, the spindle command voltage is not valid including CNC’s power ON/OFF moment. Use these signals at an applied voltage of 30 or less when signals ENB1 and 2 are OFF and at a current of 200mA or less when
  • Page 4NOTE 1 Signals SIN, *SIN, SOUT and *SOUT are for a serial spindle. These signals are not used for an analog spindle. 2 As the connector on the cable side, the solder-type 15 pin connector(FI40B-2015S, or conventional FI40-2015S) manufactured by Hirose Electric cannot be used. 3 The upper connector s
  • Page 5The position coder generates rectangular wave voltage signals in proportion to the angle of rotation of the spindle, and is used in feed per revolution and thread cutting. (1) 1 rotation of position coder with respect to 1 rotation of spindle (2) 1 rotation of position coder with respect to 2 rotati