1. Fanuc
  2. Open CNC FROM/SRAM Management Utility for CommandLine Specification

Open CNC FROM/SRAM Management Utility for CommandLine Specification Additional Manual Page 6

Additional Manual
7. Operation
This utility"FromUtil2.EXE" starts from the command line.
The progress situation and the processing result are output to the command line screen and
the specified log file.
The command line syntax for FromUtil2.EXE is as follows:
FromUtil2 [-nNode|-hHost:Port [-tTime]] [-lst|-sav|-del|-lod] [-r“path¥list_file”]
[-service] [“Target_path¥”] [-bkup|-rstr]
[-pw1=MTBpassword] [-pw2=USERpassword] [-f”path¥log_file”]
Option Function
-nNode Specify the Node number at HSSB connection (0..7)
-hHost:Port [-tTime] Specify the Host name/IP address and Port number. When the Timeout
value is not specified, it is assumed as 30 second by default.
-lst If specified, this utility writes the name of System files and User files
contained in the CNC’s FROM into the file specified by “path¥list_file”.
When the file name is written, space” ”, period”.” located on the FROM
program name is changed to underscore”_”.
-sav If specified, this utility reads the System files and User files contained in
the CNC’s FROM, and then places them under “Target_path¥”
according to the file name described in the file, “path¥list_file”.
If –service switch is not specified, the System files will not be read out.
-del If specified, this utility deletes the System files and User files contained
in the CNC’s FROM according to the file name described in the file,
“path¥list_file”.
If –service switch is not specified, the System files will not be deleted.
-lod If specified, this utility writes the System files and User files located
under “Target_path¥” into the CNC’s FROM according to the file name
described in the file, “path¥list_file”.
-r“path¥list_file”
(Note 1)
Specify the PC side file that is referred when the System files and User
files contained in CNC’s FROM are handled by any of the above
switches [-lst|-sav|-del|-lod].
-service Specify this switch in case that the System files contained in the CNC’s
FROM are handled by any of the above switches [-sav|-del].
“Target_path¥” Specify the PC side file location in case that the CNC’s FROM is
handled by any of the above switches [-sav|-lod], or in case that the
CNC’s SRAM is handled by any of the below switches [-bkup|-rstr].
-bkup If specified, this utility reads the CNC’s SRAM data and then saves it
under “Target_path¥”.
When the same name file has been located, the file is overwritten.
-rstr If specified, this utility restores the SRAM data file from “Target_path¥”
into the CNC’s SRAM area.
Ed. Date Design Description FANUC LTD. Sheet 6/9
TITLE
FANUC Open CNC
FROM/SRAM Management Utility for Command
Line Specification
A-79714E
01
04.08.12
New
DRAW.NO.
Previous page
Next page

Contents Summary of Open CNC FROM/SRAM Management Utility for CommandLine Specification Additional Manual

  • Page 1FANUC Open CNC FROM / SRAM Management Utility for Command Line Specification Edition 1.0 12-August-2004 Software Development Center FANUC LTD. The contents of this document are subject to change without notice according to the progress of development. TITLE FANUC Open CNC FROM/SRAM Management Utilit
  • Page 21. Overview On the control boards of CNC, Flash ROM modules (hereafter, “FROM”) and Static RAM modules (hereafter, “SRAM”) are mounted. In these FROM/SRAM modules, the important data that decides the CNC/PMC characteristic is stored. Typical data that stored in each module is as follows. A. FROM inc
  • Page 32. Supported functions This utility can do the following operations to FROM/SRAM data of CNC control unit from Open CNC PC side. Operation on FROM SAVE function : backs up the files stored in the FROM to any folder of PC. DELETE function : deletes the files stored in the FROM. LOAD function : restor
  • Page 44. Naming convention of stored files When FROM/SRAM data is backed up using this utility, the stored files in the PC is named as follows. For FROM files when backed up to PC When FROM files are backed up to PC side, the following file names will attached to the file automatically. FROM file name (na
  • Page 56. Preparation to start In order to execute this utility application, HSSB driver and FOCAS2 libraries (FWLIB32.DLL, FWLIB160.DLL, FWLIB16W.DLL, FWLIBE1.DLL) have to be installed to the PC beforehand. Note) In case that HSSB connection is not used, HSSB driver and FWLIB160.DLL, FWLIB16W.DLL are not
  • Page 67. Operation This utility"FromUtil2.EXE" starts from the command line. The progress situation and the processing result are output to the command line screen and the specified log file. The command line syntax for FromUtil2.EXE is as follows: FromUtil2 [-nNode|-hHost:Port [-tTime]] [-lst|-sav|-del|-
  • Page 7Option Function -pw1=MTBpassword When the User files contained in the CNC’s FROM or SRAM data is protected by the CNC parameter setting, specify the corresponding value for the MTB’s password. -pw2=USERpassword When the User files contained in the CNC’s FROM or SRAM data is protected by the CNC para
  • Page 8c) In case that [-lod] switch is used: Specify the PC file name that will be written into the CNC’s FROM by one at each line. The file names must be matched with the files located under “Target_path¥”. If semi-colon”;” is placed at the top of the line, the information of whole line is ignored. NC_BA
  • Page 94. "-del" switch ( for FROM file ) [HSSB connection] fromutil2 -n0 -del -r"C:¥fromsram¥list.txt" -service -f"C:¥fromsram¥log¥Delete.log" [Ethernet connection] fromutil2 -h"192.168.0.1:8193" -t10 -del -r"C:¥fromsram¥list.txt" -service -f"C:¥fromsram¥log¥Delete.log" 5. "-bkup" switch ( for SRAM file )