FANUC Series 30i/31i/32i-A, 31i-A5 Inverse Time Feed for the Lathe System, SPECIFICATIONS Additional Manual Page 5

Additional Manual
EDT
App
rvPersn
DATE
DESIG.
DESCRIPTION
Date
FANUC Series 30i/31i/32i-A, 31i-A5
Inverse time feed for the lathe system
A-90215EN
4/6
Name No.
Page
FANUC LTD.
Outline
When G code for inverse time feed (G93) is specified, the inverse time specification mode
(G93 mode) is set. Specify the inverse time (FRN) with an F code.
Format
G93 ; Inverse time feed command
G code (05 group)
F_ ; FRN: Feedrate command (1/min)
F code specification value FRN
F1 0.001
F1
*1
1.000
F1.0 1.000
F9999999 9999.999
F9999
*1
9999.000
F9999.9999 9999.999
*1 Value specified in fixed-point format with parameter DPI (No. 3401#0) set to 1
- G code for inverse time feed is a modal G code and belongs to group 05 (includes G
code for feed per revolution and G code for feed per minute). And G code is G93 without
regard to G code system.
- A value from 0.001 to 9999.999 can be specified as FRN, regardless of whether the input
mode is inches or metric, or the increment system is IS-B, IS-C, IS-D or IS-E.
- When an F value is specified in inverse time specification mode and the feedrate exceeds
the maximum cutting feedrate, the feedrate is clamped to the maximum cutting feedrate.
- In the case of circular interpolation, the feedrate is calculated not from the actual amount
of movement in the block but from the arc radius.
- Inverse time feed can also be used for cutting feed in a canned cycle.

Contents Summary of FANUC Series 30i/31i/32i-A, 31i-A5 Inverse Time Feed for the Lathe System, SPECIFICATIONS Additional Manual

  • Page 1TECHNICAL REPORT (MANUAL) NO. TMN05/110E Date , Oct., 2005 General Manager of Software Research Laboratory FANUC Series 30i/31i/32i-A, 31i-A5 Inverse time feed for the lathe system 1. Communicate this report to : O Your information O GE Fanuc-A, GE Fanuc-E FANUC Robotics MILACRON O Machine tool buil
  • Page 2FANUC Series 30i/31i/32i-A, 31i-A5 Inverse time feed for the lathe system SPECIFICATIONS Notice All specifications are subject to change without notice. Matters which are not especially described as possible in this document should be regarded as “impossible”. © FANUC LTD 2005 Name FANUC Series 30i/
  • Page 3TABLE OF CONTENTS Outline 4 Format 4 Explanations 5 Alarm 6 Name FANUC Series 30i/31i/32i-A, 31i-A5 Inverse time feed for the lathe system No. A-90215EN EDT DATE Date DESIG. Persn DESCRIPTION Apprv FANUC LTD. Page 2/6
  • Page 4This manual includes safety precautions for protecting the user and preventing damage to the machine. Precautions are classified into Warning and Caution according to their bearing on safety. Also, supplementary information is described as a Note. Read the Warning, Caution, and Note thoroughly befor
  • Page 5Outline When G code for inverse time feed (G93) is specified, the inverse time specification mode (G93 mode) is set. Specify the inverse time (FRN) with an F code. Format G93 ; Inverse time feed command G code (05 group) F_ ; FRN: Feedrate command (1/min) F code specification value FRN F1 0.001 *1 F
  • Page 6NOTE 1 In the inverse time specification mode, an F code is not handled as a modal code and therefore needs to be specified in each block. If an F code is not specified, alarm (PS1202 (NO F COMMAND AT G93)) is issued. 2 When F0 is specified in inverse time specification mode, alarm (PS0011 (FEED ZER
  • Page 7- To find the movement time required when F10.0 is specified 1× 60 60 TIME (sec) = = = 6.0 FRN 10 - 6(sec) is required. - For circular interpolation (G02, G03) 1 feedrate FRN = = time(min) arc radius For metric input: feedrate(mm/min), arc radius (mm) For inch input: feedrate(inch/min), arc radius (