FANUC Series 30i /31i /32i-MODEL A, Simple Spindle Electronic Gear Box, Specifications Additional Manual Page 3
Additional Manual
A-79527E
Edit
Apprv.
Desig.
Sheet
Title
Draw
No.
Date
Design
Description
Date
FANUC Series 30i/31i/32i
Simple spindle electronic gear box
Specification
Jun.18.2004
3/7
Sheet
Sheet
3 Signal
Simple spindle EGB signal SSEGB1<Gn351#0> : First spindle
SSEGB2<Gn351#1> : Second spindle
SSEGB3<Gn351#2> : Third spindle
SSEGB4<Gn351#3> : Fourth spindle
[Classification] Input signal
[Function] The Simple spindle EGB mode is turned to ON with the slave spindle which is
selected by the corresponding signal.
Note
1. This signal is effective when the parameter SEGs (No.7705#0) is
“ 1”.
2. If Simple spindle EGB mode is switched ON/OFF during both
master spindle and slave spindle are not in the stop state, the slave
spindle accelerates / decelerates immediately. Therefore, please
switch Simple spindle EGB mode ON/OFF when both master
spindle and slave spindle are in the stop state.
3. During Simple spindle EGB mode, please set the slave spindle to
Cs contouring control mode.
Simple spindle EGB mode signal SSEGBM1<Fn351#0> : First spindle
SSEGBM2<Fn351#1> : Second spindle
SSEGBM3<Fn351#2> : Third spindle
SSEGBM4<Fn351#3> : Fourth spindle
[Classification] Output signal
[Function] The Simple spindle EGB mode is ON with the slave spindle which is selected by the
corresponding signal.
[Output condition] These signals are set to 1 when:
The Simple spindle EGB mode is ON with the slave spindle which is selected by the
corresponding signal.
These signals are set to 0 when:
The Simple spindle EGB mode is OFF with the slave spindle which is selected by the
corresponding signal.
Contents Summary of FANUC Series 30i /31i /32i-MODEL A, Simple Spindle Electronic Gear Box, Specifications Additional Manual
- Page 1FANUC Series 30i /31i /32i-MODEL A Simple spindle electronic gear box Specifications - Contents - 1 GENERAL ................................................................................................................................ 2 2 SPECIFICATION .............................................
- Page 21 General On two serial spindles, it is possible to execute spindle synchronous control by input signal so that one spindle (slave spindle) follows another spindle (master spindle). To take an example of using, it is possible to execute rotary guide bush control on two spindles. 2 Specification To s
- Page 33 Signal Simple spindle EGB signal SSEGB1
- Page 4Signal address CNC PMC #7 #6 #5 #4 #3 #2 #1 #0 Gn351 SSEGB4 SSEGB3 SSEGB2 SSEGB1 PMC CNC #7 #6 #5 #4 #3 #2 #1 #0 Fn351 SSEGBM4 SSEGBM3 SSEGBM2 SSEGBM1 Signal sequence < Simple spindle EGB mode ON > Spindle rotation speed (both master spindle and slave Confirm the stop state of both master spindle an
- Page 54 Parameter #7 #6 #5 #4 #3 #2 #1 #0 7705 SEGs [Input type] Parameter input [Data type] Bit spindle SEGs When Simple spindle electronic gear box function is used, 0: Not slave spindle of Simple spindle electronic gear box function 1: Slave spindle of Simple spindle electronic gear box function When S
- Page 64036 Feed forward coefficient [Input type] Parameter input [Data type] Word spindle [Unit of data] 1% [Valid data range] 0 to 100 Set “100” to the slave spindle. 4386 Number of master-axis spindle sensor teeth [Input type] Parameter input [Data type] Word spindle [Unit of data] 1 /rev [Valid data ra
- Page 75 Note (1) This function is a basic function. But Spindle serial output option and Cs contouring control option are necessary. (2) Please switch Simple spindle EGB mode ON/OFF when both master spindle and slave spindle are in the stop state. (3) During Simple spindle EGB mode, the excess error value