FANUC Series 30i /31i /32i-MODEL A, Simple Spindle Electronic Gear Box, Specifications Additional Manual Page 5
Additional Manual
A-79527E
Edit
Apprv.
Desig.
Sheet
Title
Draw
No.
Date
Design
Description
Date
FANUC Series 30i/31i/32i
Simple spindle electronic gear box
Specification
Jun.18.2004
5/7
Sheet
Sheet
4 Parameter
#7 #6 #5 #4 #3 #2 #1 #0
7705
SEGs
[Input type] Parameter input
[Data type] Bit spindle
SEGs When Simple spindle electronic gear box function is used,
0: Not slave spindle of Simple spindle electronic gear box function
1: Slave spindle of Simple spindle electronic gear box function
When Simple spindle electronic gear box function is used, the above parameter bit for the
slave spindle is set to 1.
#7 #6 #5 #4 #3 #2 #1 #0
4395
ESYEGB
[Input type] Parameter input
[Data type] Bit spindle
ESYEGB Simple spindle electronic gear box function is
0: Disable
1: Enable
Both bits for master spindle and slave spindle are set to “1”.
#7 #6 #5 #4 #3 #2 #1 #0
4352
SPEGBM
SPEGBS
FFALWS
[Input type] Parameter input
[Data type] Bit spindle
SPEGBM Setting for the Simple spindle electronic gear box function master axis
0 : Non-spindle EGB master axis
1 : Spindle EGB master axis
Set this parameter to the master spindle.
SPEGBS Setting for the Simple spindle electronic gear box function slave axis
0 : Non-spindle EGB slave axis
1 : Spindle EGB slave axis
Set this parameter to the slave spindle.
FFALWS Feed-forward setting
0 : Feed-forward is enabled only during cutting feed.
1 : Feed-forward is always enabled.
Set this parameter to the slave spindle.
Contents Summary of FANUC Series 30i /31i /32i-MODEL A, Simple Spindle Electronic Gear Box, Specifications Additional Manual
- Page 1FANUC Series 30i /31i /32i-MODEL A Simple spindle electronic gear box Specifications - Contents - 1 GENERAL ................................................................................................................................ 2 2 SPECIFICATION .............................................
- Page 21 General On two serial spindles, it is possible to execute spindle synchronous control by input signal so that one spindle (slave spindle) follows another spindle (master spindle). To take an example of using, it is possible to execute rotary guide bush control on two spindles. 2 Specification To s
- Page 33 Signal Simple spindle EGB signal SSEGB1
- Page 4Signal address CNC PMC #7 #6 #5 #4 #3 #2 #1 #0 Gn351 SSEGB4 SSEGB3 SSEGB2 SSEGB1 PMC CNC #7 #6 #5 #4 #3 #2 #1 #0 Fn351 SSEGBM4 SSEGBM3 SSEGBM2 SSEGBM1 Signal sequence < Simple spindle EGB mode ON > Spindle rotation speed (both master spindle and slave Confirm the stop state of both master spindle an
- Page 54 Parameter #7 #6 #5 #4 #3 #2 #1 #0 7705 SEGs [Input type] Parameter input [Data type] Bit spindle SEGs When Simple spindle electronic gear box function is used, 0: Not slave spindle of Simple spindle electronic gear box function 1: Slave spindle of Simple spindle electronic gear box function When S
- Page 64036 Feed forward coefficient [Input type] Parameter input [Data type] Word spindle [Unit of data] 1% [Valid data range] 0 to 100 Set “100” to the slave spindle. 4386 Number of master-axis spindle sensor teeth [Input type] Parameter input [Data type] Word spindle [Unit of data] 1 /rev [Valid data ra
- Page 75 Note (1) This function is a basic function. But Spindle serial output option and Cs contouring control option are necessary. (2) Please switch Simple spindle EGB mode ON/OFF when both master spindle and slave spindle are in the stop state. (3) During Simple spindle EGB mode, the excess error value