1. Fanuc
  2. FANUC Series 16i/18i/21i One Touch Macro call function

FANUC Series 16i/18i/21i One Touch Macro call function Additional Manual Page 5

Additional Manual
4/11
A- 77823E
DRAW.No.
FANUC Series 16i /18i /21i
Specifications of One Touch Macro call
Title
Timing chart,etc. is changed
Newly registration
DESCRIPTION
A.Fukumoto
DESIGNE
29.Jul.1999
02.Jul.1999
DATE
02
01
EDIT.
E.Gennma
2.2 Interruption of sequence
2.2.1 Interruption by reset or emergency stop
The abnormal end signal (MCSP) becomes “1” when the operation is interrupted by reset or
emergency stop, and the execution of the program is stopped. At this time, the mode change
request signal (MCRQ) and mode notification signal are output to recover the mode, and
the selection program number is recovered automatically.
Please set “1” in mode change completion signal (MCFIN) on the PMC side to complete the
sequence.
2.2.2 Feed hold or single block
The abnormal end signal (MCSP) is not output when stopping in feed hold or single block.
Under such a condition, when the cycle start signal (ST) is turned on and off, the continuity
of the macro program is executed.
Under such a condition, even if macro call start signal (MCSTx) is turned on and off, it is
not effective.
Under such a condition, when reset or emergency stop are input, the operation which is
described in 2.2.1 is executed.
2.2.3 Stop by alarm
When the execution of macro program is stopped by alarm, the abnormal end signal
(MCSP) is output.
Under such a condition, when reset or the emergency stop are input, the operation which is
described in 2.2.1 is executed.
Following Fig.2 shows the timing chart of each signal when the sequence is interrupted by
alarm.
Previous page
Next page

Contents Summary of FANUC Series 16i/18i/21i One Touch Macro call function Additional Manual

  • Page 1TECHNICAL REPORT (MANUAL) ＮＯ．ＴＭＮ ９９／175E ＮＯ．ＴＭＮ ９９／175E Date: Dec. 20, 1999 General Manager of Software Laboratory FANUC Series 16i/18i/21i One Touch Macro call function 1. Communicate this report to: Your information ○ GE Fanuc-N, GE Fanuc-E FANUC Robotics CINCINNATI MILACRON ○ Machine tool builder
  • Page 2FANUC Series 16i / 18i / 21i Specifications of One Touch Macro call CONTENTS 1. Outline 2 2. Specification 2 3. Signal 7 4. Parameter 10 5. Alarm 11 TitleFANUC Series 16i /18i /21i Specifications of One Touch Macro call 02 29.Jul.1999 Timing chart,etc. is changed 01 02.Jul.1999 A.Fukumoto Newly regi
  • Page 31. Outline This function enables the following three operations in pushing the switch installed in the machine only by the change in a minimum LADDER program. (1) Changes to MEM mode. (2) Execution of macro program registered in memory. (3) Return to the mode before macro program is executed. And th
  • Page 4• End of macro program (6) Please instruct M02 or M30 at the end of the macro program. Moreover, please input external reset signal (ERS) or reset&rewind signal (RRW) with M02 or M30 on the PMC side. The program which had been selected before the macro is executed is automatically selected by reset.
  • Page 52.2 Interruption of sequence 2.2.1 Interruption by reset or emergency stop The abnormal end signal (MCSP) becomes “1” when the operation is interrupted by reset or emergency stop, and the execution of the program is stopped. At this time, the mode change request signal (MCRQ) and mode notification s
  • Page 6Least 32ms 02 MCST (PMC→CNC) MCRQ (CNC→PMC) Mode notification MEM before macro execution signal(CNC→PMC) Mode Change process(PMC) 02 MCFIN (PMC→CNC) 02 Mode indefinite MEM before macro execution MCEXE (CNC→PMC) MCEXx (CNC→PMC) Program Execution (CNC) AL (Alarm) (CNC→PMC) MCSP (CNC→PMC) Reset Fig.2 T
  • Page 72.3 Notes (1) Even if the macro call is being executed, mode selection signal (MD1,MD2,MD4) is effective. Therefore, please change the LADDER program to disable the mode change when the macro call executing signal (MCEXE) is “1” when the inconvenience is caused if the mode change is done. (2) Other
  • Page 83. Signal 3.1 Signal list The list of the signal used by this function is shown as follows. In this function, R signal is used instead of G and F signal. Address “n” in the table below is specified by parameter No.6097. 02 Address #7 #6 #5 #4 #3 #2 #1 #0 R(n) MCST8 MCST7 MCST6 MCST5 MCST4 MCST3 MCST
  • Page 93.2 The detail of signal • Macro call start signal MCSTx [Classification] Input signal [Function] This signal starts the macro call sequence. [Operation] When the standing fall of this signal is detected, CNC starts the corresponding macro program. O number of the program started b
  • Page 10• Mode notification signal MD1R, MD2R, MD4R, DNCIR, and ZRNR [Classification] Output signal [Function] This signal notifies the mode which should be changed. [Output condition] This signal is set to "1" in the following case: - When CNC detects the standing fall of Macro call start signal (
  • Page 114. Parameter 6095 The number of programs used by the macro call function 02 Data type : Byte Unit of data : Number Valid data range : 0 to 16 Specify the number of programs used by the macro call function. For instance, when three is set, macro call start signal MCST1, MCST2, and MCST3 become effect
  • Page 125. Alarm Number Message Contents 059 PROGRAM NUMBER NOT FOUND The program of the specified O number is not registered in the memory. 5306 MODE CHANGE ERROR The mode is not correctly changed at start 02 of sequence. 02 TitleFANUC Series 16i /18i /21i Specifications of One Touch Macro call 02 29.Jul.1