1. Fanuc
  2. FANUC Series 16i/18i/21i-B, Specification Cyrillic Alphabet Display

FANUC Series 16i/18i/21i-B, Specification Cyrillic Alphabet Display Additional Manual Page 5

Additional Manual
5
Edit
Apprv.
Apprv.Apprv.
Apprv.Desig.
Desig.Desig.
Desig.
Sheet
Title
Draw
No.
/
7
Date
DateDate
Date
Design
DesignDesign
Design
Descri
p
tion
Descri
p
tionDescri
p
tion
Descri
p
tion
Date
DateDate
Date
FANUC Series16i /18i/21i -B
Cyrillic alphabet display
A
-76572EN
2004.12.06
S.ISOHATA
Addition of method of instructing in G240 K0 2004.12.15
ISOHATA
2
Example 1) When you display Cyrillic alphabet “Б" (Cyrillic alphabet display mode
ON)
The Cyrillic alphabet code of “Б" is C1. (It is 193 in the decimal number)
G240 K2;
G243 X10. Y10. C193;
Example 2) When you display Cyrillic alphabet “A” (Cyrillic alphabet display mode
OFF)
FANUC character code of “A" is 41. (It is 65 in the decimal number)
G240 K0;
G243 X10. Y10. C65;
The function of the command address by other G243(K,B,F,Z,D,P) instructions is
similar to the specification of a usual character display command. (Please refers to
the manual clause (B-61803-1)6.1.2 for the use of each address.)
Previous page
Next page

Contents Summary of FANUC Series 16i/18i/21i-B, Specification Cyrillic Alphabet Display Additional Manual

  • Page 1FANUC Series 16i /18i /21i - B Specification Cyrillic alphabet display Index 1. Outline 2 2. Specification 2 3. Character- code table 6 4. Correspondence edition 7 Title FANUC Series16i /18i/21i -B Cyrillic alphabet display Draw No. A-76572EN 2 2004.12.15 ISOHATA Addition of method of instructing in
  • Page 21. Outline The thing to display the Cyrillic alphabet (Russian) can be done in the conversation macro. 2. Specification The display command of the Cyrillic alphabet is done with G243 (character display command) as well as a usual character display instruction. However, there are two kinds of instruc
  • Page 3Cyrillic alphabet “Б" is displayed at the position of character coordinate system (10,10) when instructing. Note) Please omit and specify high-ranking '00' when you specify the Cyrillic alphabet code. For instance, it is not correctly displayed when instructing as ("00C1"). Example 2) When instructi
  • Page 4B) For Cyrillic alphabet display mode OFF(G240 K0) The Cyrillic alphabet display mode is turned off after it instructs of this, and character-code A8 and C0-DF are distinguished as not the Cyrillic alphabet code but FANUC character code. (Refer to the character-code of clause 3 table) The method of
  • Page 5Example 1) When you display Cyrillic alphabet “Б" (Cyrillic alphabet display mode ON) The Cyrillic alphabet code of “Б" is C1. (It is 193 in the decimal number) G240 K2; G243 X10. Y10. C193; Example 2) When you display Cyrillic alphabet “A” (Cyrillic alphabet display mode OFF) FANUC character code o
  • Page 63. Character- Character-code table The character-code, which can be used by this function, is the following tables and the melons. Please specify it by the method of displaying usual excluding these characters. Russian character FANUC code Cyrillic code А 41 C0 Б 0FA0 C1 В 42 C2 Г 0FA1 C3 Д 0FA2 C4
  • Page 74. Correspondence edition The series and edition of the macro library to which this function is applied are as follows. A) Library where specification (G240 K2) by Cyrillic alphabet code is possible. FS16i-MB : BZL1-DA FS18i-MB : BZM1-DA FS21i-MB : DZ82-DA FS16i-TB : BZL2-DA FS18i-TB : BZM2-DA FS21i