FANUC Series 16i/18i/21i -TB/MB Spindle Speed Override for Each Spindle (Improvement of Multi-Spindle Control) Additional Manual Page 5
Additional Manual
A-79118E
Edit
Apprv. Desig.
Sheet
Title
Draw
No.
Date
Design
Descri
p
tion
Date
FANUC Series 16i/18i/21i –TB/MB
Spindle speed override for each spindle
(Improvement of multi-spindle)
Sheet
5
/
5
5.Note
- The multi-spindle control option is necessary to use this function.
- In the case of parameter SOV (No.3106#5) (the spindle override value is displayed)=1, 1st spindle speed override value is
displayed.
- During constant surface speed control, the spindle speed is overridden after it is clamped at the value specified in the
maximum spindle speed clamp command (G50S_ for T series and G92S_ for M series). So, please be careful because
the actual spindle speed may exceed the value specified in the spindle speed clamp command.
Parameter SOC (No.3708#5)(during constant surface speed control, the speed clamp is carried out after spindle speed
override) is disabled. Even if this parameter is set, above note is not changed.
But above limit to the spindle speed (No.3772,3802,3822,3850) can be applied to clamp the spindle speed.
- During this function, there is no function to fix the override to 100% during tapping cycle mode (G84,G74 for M series and
G84,G88 for T series) and thread cutting mode (G33 for M series and G32,G92,G76 for T series). So, please set an
override value by ladder as required.
- Parameter No.5131(setting chamfering angle in threading cycle) can not be used. Please set 0 to this parameter.
- Set an override value to 100% for spindles whose speeds are not specified override.
- The spindle override isn't effective in the spindle which is controlled spindle speed with PMC.
- On FANUC Series 21i- MODEL B, PMC- SB7 is necessary.
6.Reference item
FANUC Series 16i/18i/21i- MODEL B multi-spindle control type C specifications (A-79114E)
Contents Summary of FANUC Series 16i/18i/21i -TB/MB Spindle Speed Override for Each Spindle (Improvement of Multi-Spindle Control) Additional Manual
- Page 1FANUC Series 16i/18i/21i -TB/MB Spindle speed override for each spindle (Improvement of multi-spindle control) Specifications FANUC Series 16i/18i/21i –TB/MB Title Spindle speed override for each spindle (Improvement of multi-spindle) Draw A-79118E No. Edit Date Design Description Sheet 1/5 Date Des
- Page 21.General During this function, each spindle speed can be overridden individually. An override value to 0%~254% can be applied. This function can be used when multi-spindle control type C (parameter MSC (No.3713#3)) is set. This function requires multi-spindle control option. 2.Specification When ea
- Page 3SOV0#2~7#2 SOV0#1~7#1 1st spindle#2 override override 1st spindle#1 S command SOV20#2~27#2 SOV20#1~27#1 2nd spindle#2 override override 2nd spindle#1 SOV30#2~37#2 SOV30#1~37#1 path 2 path 1 3rd spindle#2 override override 3rd spindle#1 Fig.4 Parameter EOV(No.3713#4)=1 (two-path) 3.Signals Spindle sp
- Page 44.Parameter #7 #6 #5 #4 #3 #2 #1 #0 3713 EOV [Data type] Bit, common to all path EOV Each spindle speed override is 0: not used 1: used NOTE 1) Multi-spindle control type C (No.3713#3=1) is necessary to use this function. NOTE 2) When this parameter has been set, the power must be turned off before
- Page 55.Note - The multi-spindle control option is necessary to use this function. - In the case of parameter SOV (No.3106#5) (the spindle override value is displayed)=1, 1st spindle speed override value is displayed. - During constant surface speed control, the spindle speed is overridden after it is cla