1. Fanuc
  2. Changing BIOS Setting in the Fanuc Open CNC (A-76035E/01)

Changing BIOS Setting in the Fanuc Open CNC (A-76035E/01) Additional Manual Page 4

Additional Manual
2. Confirming the hard disk capacity
1) Please move the cursor to “System Summary” of the menu screen and push the [Enter]
key.
2) After confirming the item of “Hard Disk Drive 0” is displayed like the list shown
below, please go to the next step; “Changing the setting value”. In the case that the
value is different from the list shown below, please do not change the value of setting.
Because the specification of the HDD unit are different from applied model.
Hard Disk
Specification of HDD unit Manufacturer / Model
Value of “Hard Disk Drive 0”
A02B-0207-C054 HITACHI / DK223A-11 1081 MB
A02B-0207-C057 HITACHI / DK225A-14 1440 MB
3. Changing the setting value
1) Move the cursor to “Power Management” of the menu screen and push the [Enter] key.
2) Please change the setting value like the next table.
Item Contents
Doze Timer
It must be “Disable(default)”
Sleep Timer
It must be “Disable(default)”
IDE Standby Timer
FANUC change this item from Disable(default) to 10 min.
3) After changing the value, push the [Esc] key, then it returns to the menu screen.
4. Exiting the Setup Utility
1) Move the cursor to “Exit Setup” of the menu screen and push the [Enter] key.
2) Move the cursor to “Yes, Save and exit the Setup Utility.” and push the [Enter] key.
The PC function reboot automatically with new setting values.
EDIT.
FANU
C
LTD
FANUC LTDFANUC LTD
FANU
C
LTD
SHEET
DRAW. NO.
CUST.
TITLE
003/
DESCRIPTIONDESIG.DATE
Changing BIOS setting
in the FANUC OPEN CNC
A
-76035E/01
Previous page
Next page

Contents Summary of Changing BIOS Setting in the Fanuc Open CNC (A-76035E/01) Additional Manual

  • Page 1
  • Page 2Changing BIOS setting in the FANUC OPEN CNC Outline The power management of the HDD (Hard Disk Drive) in the FANUC OPEN CNC system such as MMC-IV, Intelligent Terminal, Series 160i/180i/210i is controlled by the BIOS software (Basic Input Output System). In accordance with present BIOS setting value
  • Page 3(C) Copyright IBM Corporation 1981,1994 ALL RIGHTS RESERVED ~~~~ ~~ 486DX2-50MHz ~~~~ ~~ ~~~~ ~~ Copyright (C) Matsushita Electric Industrial Co.,LTD 1995 Release 01 2.00 0640KB System Memory Please push “F1” key while this 7168KB Extended Memory rectangle is displayed. The Setup utility is started.
  • Page 42. Confirming the hard disk capacity 1) Please move the cursor to “System Summary” of the menu screen and push the [Enter] key. 2) After confirming the item of “Hard Disk Drive 0” is displayed like the list shown below, please go to the next step; “Changing the setting value”. In the case that the v
  • Page 5About the BIOS standard setting value The BIOS setting value that is set by BIOS program automatically is called “the BIOS default setting value”. FANUC changes with regard to the item that was shown in the table of the next page to “the BIOS default setting value”. The BIOS setting value of factory
  • Page 6Technical Notice 1. Please set the Doze Timer setting and also Sleep Timer setting of the setup utility just as Disable. 2. In the case that the IDE Standby Timer setting of the setup utility is set to “10 min”, when it passes for about 10 minutes without the access to the HDD being carried out, the