1. Fanuc
  2. Series 30i-A/31i-A5, 16i-MB/18i-MB5/16i-TB, 15i-MB

Series 30i-A/31i-A5, 16i-MB/18i-MB5/16i-TB, 15i-MB Additional Manual Page 4

Additional Manual
FS30i-A/31i-A5,FS16i-MB/18i-MB5/16i-TB,FS15i-MB Table of the Parameters for 5-Axis Machining Features(A-79370E) 4/10
(2) The parameters described on each table are used for each applied feature.
2-1) Table A
<Applied features>
FS30i-A : Tilted working plane command(A02B-0303-S676), Tool center point control for 5-axis machining(A02B-0303-S677), Tool radius compensation for
5-axis machining(A02B-0303-S667), Manual feed for 5-axis machining(A02B-0303-S679)
FS31i-A5 : Tilted working plane command(A02B-0306-S676), Tool center point control for 5-axis machining(A02B-0306-S677), Tool radius compensation for
5-axis machining(A02B-0306-S667), Manual feed for 5-axis machining(A02B-0306-S679)
FS16i-MB : Tilted working plane command(A02B-0282-S676), Tool center point control for 5-axis machining(A02B-0282-S677), Tool radius compensation for
5-axis machining(A02B-0282-S667), Manual feed for 5-axis machining(A02B-0282-S679)/In case of Tool radius compensation for 5-axis machining,
<Table A> is available when parameter No.19607#4 is set to “1”.
FS18i-MB5 : Tilted working plane command(A02B-0284-S676), Tool center point control for 5-axis machining(A02B-0284-S677), Tool radius compensation for
5-axis machining(A02B-0282-S667), Manual feed for 5-axis machining(A02B-0284-S679) /In case of Tool radius compensation for 5-axis machining,
<Table A> is available when parameter No.19607#4 is set to “1”.
FS16i-TB : Tool center point control for 5-axis machining(A02B-0281-S677), ), Manual feed for 5-axis machining(A02B-0281-S679)
FS15i-MB : Tilted working plane command(A02B-0298-J959), Tool center point control for 5-axis machining(A02B-0298-J958)
Parameter No.
FS30i-A
/31i-A5
FS16i-MB
/18i-MB5
/16i-TB
FS15i-MB
Contents
Note
- 19607#4 - In case of Tool radius compensation for 5 axis machining on FS16i-MB,FS18i-MB5
0 : <Table B,C,D> is available.
1 : <Table A> is available.
19665#4 19665#4 7540#4 The controlled point is shifted by:
0 : Automatic calculation.
1 : Using parameter No. 19667.
19665#5 19665#5 7540#5 The controlled point is:
0 : Not shifted.
1 : shifted.
Previous page
Next page

Contents Summary of Series 30i-A/31i-A5, 16i-MB/18i-MB5/16i-TB, 15i-MB Additional Manual

  • Page 1FANUC Series 30i-A/31i-A5, FANUC Series 16i-MB/18i-MB5/16i-TB FANUC Series 15i-MB Table of the parameters for 5-axis machining features 1.Type of applied technical documents Name Spec.No./Ed. 2.Summary of Change New, Add, Applicable Group Name/Outline Correct, Date Delete Basic Option Explanation fo
  • Page 23-D cutter compensation, Cutter compensation for rotary table, 3-D cutter compensation for rotary table, Tool length compensation in tool axis direction, 3-D handle feed Unit Maintenance Parts Notice There are many parameters for 5-axis machining features. So, on this document, they are summed up fo
  • Page 3FANUC Series 30i-A/31i-A5, FANUC Series 16i-MB/18i-MB5/16i-TB, FANUC Series 15i-MB Table of the Parameters for 5-Axis Machining Features (1) The parameters for the following 5-axis machining features on FS30i-A/31i-A5, FS16i-MB/18i-MB5/16i-TB and FS15i-MB are described. Refer to each table(Table
  • Page 4(2) The parameters described on each table are used for each applied feature. 2-1) Table A FS30i-A : Tilted working plane command(A02B-0303-S676), Tool center point control for 5-axis machining(A02B-0303-S677), Tool radius compensation for 5-axis machining(A02B-0303-S667), Manual
  • Page 519666 19666 7548 Tool holder offset for tool axis direction tool length compensation 19667 19667 7745 Controlled-point shift vector - 19720 - Axis number of linear axis 1 (Note 1) - 19721 - Axis number of linear axis 2 (Note 1) - 19722 - Axis number of linear axis 3 (Note 1) 19680 19680 6161 Mechani
  • Page 619712 19712 6193 Intersection offset vector between the second and first rotation axes of the tool (X-axis of the basic three axes) 19713 19713 6194 Intersection offset vector between the second and first rotation axes of the tool (Y-axis of the basic three axes) 19714 19714 6195 Intersection offset
  • Page 72-2) Table B FS16i-MB : Tool radius compensation for 5-axis machining(A02B-0282-S667) for Tool rotation type machine / is available when the parameter No.19607#4 is set to “0”. FS18i-MB5 : Tool radius compensation for 5-axis machining(A02B-0284-S667) for Tool rotation ty
  • Page 82-3) Table C FS16i-MB : Tool radius compensation for 5-axis machining(A02B-0282-S667) for Rotary table type machine /
    • is available when the parameter No.19607#4 is set to “0”. FS18i-MB5 : Tool radius compensation for 5-axis machining(A02B-0284-S667) for Rotary table type
  • Page 92-4) Table D FS16i-MB : Tool radius compensation for 5-axis machining(A02B-0282-S667) for Mixed-type machine /
    • is available when the parameter No.19607#4 is set to “0”. FS18i-MB5 : Tool radius compensation for 5-axis machining(A02B-0284-S667) for Mixed-type machine /
  • Page 102-5) Table E FS30i-A : Tool length compensation along tool direction(A02B-0303-S670) FS31i-A5 : Tool length compensation along tool direction(A02B-0306-S670) FS16i-MB : Tool length compensation along tool direction(A02B-0282-S670) FS18i-MB5 : Tool length compensation along tool di