1. Fanuc
  2. Fanuc Servo Check Board Descriptions (A-72569EN-021)

Fanuc Servo Check Board Descriptions (A-72569EN-021) Additional Manual Page 11

Additional Manual
11
/
13Descri
p
tionDateEd
01 98.12.14
SHEET
DRAW. No.
CUST.
TITLE
Hamatani Newl
y
desi
g
ned
SERVO CHECK BOARD
DESCRIPTIONS
A-72569EN-021
FANUC LTD
Desi
g
.
7. TROUBLE SHOOTING
7.1. LSI ERROR turns ON
1) Please measure the voltage between 5VEX and GND of TM1.
If it is less than 4.75V, the capability of CNC power supply is not enough.
Please remove a short piece attached to 5VIN and 5VEX of TM1 and connect external power
supply between 5VEX and GND.
2) OFF and ON the CNC power.
If the problem does not solved after all, the Servo Check Board may be damaged.
7.2. Analog Output does not work
Please check RECV indicator of the channel. If it is OFF, the data may not be sent from the
DSP.
Please check following items.
1) Is the Channel Setting value correct?
2) TSA(DATA=2) does not sent from DSP when No.2115(No.1726 in FS15) is zero.(except
digital servo software 90A0 series)
No.2206(1746 in FS15)#7 must be zero if digital servo software is 90A0 series.
7.3. Digital Output does not work
(with Servo Tuning Software or Servo Auto Tuning Software)
1) Please check if all RECV indicator to be measured are ON.
If not, refer to “Analog Output does not work” above.
2) If PC ACCESS indicator does not turn ON nor blink during the tuning software runs on PC,
check cable connection between Servo Check Board and PC and printer port number
setting(LPTx) on PC.
3) The printer port mode of PC must be set to “bi-directional” mode. It can be check and change
in BIOS setting menu in many PCs. To open BIOS setting menu, refer to the manuals of your
PC.
Note: some PC can not set the printer port mode to bi-directional. In this case, Servo Tuning
Software or Servo Auto Tuning Software can not be used on the PC.
7.4. Channel Setting value does not keep the last value when the power turned off.
A EEPROM(reference No.D12 on the board) may be damaged. Please contact our service
section and exchange this device.
The endurance is about 100,000 times of channel number change.
Previous page
Next page

Contents Summary of Fanuc Servo Check Board Descriptions (A-72569EN-021) Additional Manual

  • Page 1FANUC SERVO CHECK BOARD A06B-6057-H630 DESCRIPTIONS SERVO CHECK BOARD TITLE DESCRIPTIONS DRAW. No. 01 98.12.14 Hamatani Newly designed A-72569EN-021 CUST. SHEET Ed Date Desig. Description FANUC LTD 1/13
  • Page 2A Servo Check Board provides the way to measure numerical data inside the Digital Servo used for control. The data can be measured as analog voltage and digital signal (available with Servo Auto Tuning Function). 1. FEATURES 1) Analog and Digital in one (compatible with old products). The same funci
  • Page 3Reference Descriptions CNI1 Connector for 1st/2nd axis input. Can not use with CNI3 at the same time. * CNI2 Connector for 3rd/4th axis input. Can not use with CNI3 at the same time. * CNI3 Connector for 1st upto 4th axis input. * Can not use with CNI1 nor CNI2 at the same time. CNI4 Connector for 5
  • Page 43. CONNECTION DIAGRAM ATTENNTION: No adapters nor cables to connect with CNC or β=Series Amplifier are included with this Servo Check Board. Please order adapter and cables separately as shown below. For more details, please refer connection diagrams shown from next page. kind of CNC/Amplifier neces
  • Page 5●Series 15-i,16-i,Power Mate i-MODEL H, Power Mate i-MODEL D CNC cable A06B-6050-K872 adapter cable TESTA CNI3 CA54 CN0 TESTB CNI4 adapter board Servo Check Board A06B-6057-H630 adapter board and cable A02B-0236-K822 * Connection between TESTB and CNI4 is required only when axes after 5th axis are m
  • Page 6●Power Mate-MODEL H Power Mate cable -MODEL H A06B-6050-K872 JA23 CNI3 CNI4 Servo Check Board JA24 A06B-6057-H630 * Connection between JA24 and CNI4 is required only when axes after 5th axis are measured. ●Series 0-C,15-A,21-TA, Power Mate preventing reverse insertion cable CNI1 CNI2 CNC A06B-6050-K
  • Page 7●Power Mate-MODEL E preventing reverse CNI1 insertion cable A06B-6050-K871 Power Mate -MODEL E adapter cable CNIN CNOUT CNI3 JA20 CNI4 adapter board for Power Mate-E Servo Check Board adapter board and cable A06B-6057-H630 A02B-0168-K021 ●SERVO AMPLIFIER β series I/O Link Option preventing reverse C
  • Page 84. CHANNEL SETTING The block diagram below show the internal structure of the Servo Check Board. Channel Setting is used to select the kind of data from the data sent from DSPs, displayed on eight 7-segment LEDs and changed by four push switches. Channel Setting (7 segment LED x 8 , four push switch
  • Page 9Example: the case of measurement below. CH1: X axis(axis number=1) TCMD CH2: X axis(axis number=1) VCMD CH3: X axis(axis number=1) TSA CH4: Y axis(axis number=2) TSA Set digits as below. 11 10 12 22 CH1 CH2 CH3 CH4 5. ANALOG OUTPUT The selected data is output to check pins as analog voltage. The rel
  • Page 106. DIGITAL OUTPUT ● In the case of Servo Auto Tuning Function. An old Interface Board(A06B-6057-H620)can be replaced by this Servo Check Board for Servo Auto Tuning Function. * difference from old interface board(A06B-6057-H620) Please set digits as below. 15 25 35 45 CH1 CH2 CH3 CH4 For detail, ple
  • Page 117. TROUBLE SHOOTING 7.1. LSI ERROR turns ON 1) Please measure the voltage between 5VEX and GND of TM1. If it is less than 4.75V, the capability of CNC power supply is not enough. Please remove a short piece attached to 5VIN and 5VEX of TM1 and connect external power supply between 5VEX and GND. 2) O
  • Page 128. EXTERNAL DIMENSIONS SERVO CHECK BOARD TITLE DESCRIPTIONS DRAW. No. 01 98.12.14 Hamatani Newly designed A-72569EN-021 CUST. SHEET Ed Date Desig. Description FANUC LTD 12/13
  • Page 139. SPECIFICATIONS Item Specifications Product Name FANUC Servo Check Board Part No. A06B-6057-H630 available CNC Series 0-C, 15, 16, 20, 21(include i series) Power Mate(include i series) β series SERVO AMPLIFIER(I/O Link Option) dimensions 150(W) ×135(D) ×33(H)(except projected connector over the bo