0i-PB Specifications Additional Manual Page 2
Additional Manual
Specifications for Series 0
i
-PB
01 Edition
0i
PB
Controlled path 1 path
○
Controlled axis
(Including Cs axes)
4 axes
○
Simultaneously controlled
axes
Max. 4 axes
○
Axis control by PMC
○
○
○
○
0.01mm, 0.01ｄｅｇ 0.001ｉｎｃｈ
○
0.001mm, 0.001ｄｅｇ, 0.0001ｉｎｃｈ
○
Optional DMR
○
○
○
○
○
All axes/each axis
○
○
○
○
○
Only for G00
○
○
Each axis
○
○
○
○
○
○
○
○
☆
○
○
○
○
○
○
○
○
○
○
○
○
○
Max. 3 units
○
×1, ×10, ×m, ×n m：0～127, ｎ：0～1000
○
ｘ1, ｘ10, ｘ100, ｘ1000
○
○
MDI operation
Schedule function
Program number search
Manual handle feed rate
Sequence number comparison and stop
Buffer register
Dry run
Single block
Reader/puncher interface is required.
C axis backlash compensation for each
index
Stored pitch error compensation
JOG feed
Manual reference position return
Manual handle feed
Jog and handle simultaneous mode
Incremental feed
All axes/each axis/each direction/block start/cutting
Machine lock
Linear scale I/F with absolute address
reference mark
Emergency stop
Overtravel
Stored stroke check 1
Safety zone check
Position switch
Backlash compensation for each rapid
traverse and cutting feed
Backlash compensation
Inch/metric conversion
Interlock
Follow-up
Servo off
Stored stroke check 2
Stroke limit check before move
Mirror image
Flexible feed gear
Fine Acc & Dec control
Servo HRV control
Basic two axes are X and Y, additional axes are
optional from Z, U, V, W, A, B and C.
Least input increment
Max. simultaneous 4 axes
Axis name
T axis control
C axis control
Machine
controlled axes
Item Specifications
Controlled axis
Reference position setting without DOG
Operation
Automatic operation (memory)
DNC operation
Sequence number search
：Standard ●：Standard option ：Option ＊：Function included in another option －：Not available
Note) Some combinations of these options are restricted.
In case of CNC Display with Personal Computer function, using CNC Screen Display Function is a premise.
1 A-80943E/01
Contents Summary of 0i-PB Specifications Additional Manual
- Page 1TECHNICAL REPORT (MANUAL) ＮＯ．ＴＭＮ0３／048E Date June,02 2003 General Manager of CNC Laboratory Series 0i-PB Specifications １．Communicate this report to: O Your information only O GE Fanuc-A, GE Fanuc-E FANUC Robotics CINCINNATI MILACRON O Machine tool builder Sales agency End user ２．Summary for Sales D
- Page 2Specifications for Series 0i -PB 01 Edition ：Standard ●：Standard option ：Option ＊：Function included in another option －：Not available Note) Some combinations of these options are restricted. In case of CNC Display with Personal Computer function, using CNC Screen Display Function is a premise. 0i
- Page 30i Item Specifications PB Interpolation functions Positioning G00 (Linear interpolation type positioning is possible) ○ Exact stop mode G61 ○ Exact stop G09 ○ Linear interpolation ○ Circular interpolation Multi-quadrant is possible ○ Dwell Dwell in seconds ○ Helical interpolation Circular interpolat
- Page 40i Item Specifications PB G code system A/B ○ Pattern function ○ Nibbling G68, G69, M code ○ Pattern base point command G72 ○ Memory and call by A/B macro 5 ○ U/V/W macro ○ Multi-piece machining ○ Command for restarting multi-piece ○ machining Repositioning G75, M code ○ Bending compensation G38, G3
- Page 50i Item Specifications PB Actual cutting feedrate display ○ Directory display of floppy cassette ○ Directory display and punch for each ○ group Graphic function Display unit with graphic is required. ☆ Servo setting screen ○ Servo waveform display Display unit with graphic is required. ＊ Display of
- Page 60i Item Specifications PB Others NC ready, servo ready, automatic operation, automatic operation start lamp, feed hold, reset, NC Status output signal ○ alarm, distribution end, rewinding, inch input, cutting, inposition, thread cutting, tapping, etc. 9" monochrome CRT/MDI ● 7.2" monochrome LCD/MDI
- Page 7Software of personal computer part in case of the CNC system which is connected with personal computer via HSSB(High Speed Serial Bus) Items Specifications Remarks Operating system Windows® 2000 *4 Extended library FOCAS1 *7 CNC basic operation package Option CNC screen display function Option Softw
- Page 8(Note) *1 : There are some limitations in case of CNC Display with Personal Computer Function. *2 : Only for CNC Display with Personal Computer Function. *3 : The actual registrable value might changes according to the registered number of programs and the program si *4 : Intel, Pentium are register