0i-PB Specifications Additional Manual Page 3
Additional Manual
0i
PB
Item Specifications
○
G61
○
G09
○
○
Multi-quadrant is possible
○
○
○
G31
○
○
G28
○
○
Max. 240m/min (1μm)
○
25, 50, 75, 100%
○
○
X, Y axis: 7 steps
○
X, Y axis: 2 ste
p
s
○
X, Y axis: 7 ste
p
s
(
Onl
y
for
p
ositionin
g)
○
○
○
Rapid traverse: linea
r
Cuttin
g
feed: ex
p
onential
○
0～254%
○
0～655.34%
○
○
○
○
1 cycle/continuity
○
G70
○
○
○
○
By nibbling pitch
○
EF output
○
EIA RS244/ISO840
○
○
Horizontal and vertical parity
○
○
9
○
±8桁
○
O4-digit
○
○
N5-digit
○
Combined use in the same block
○
○
○
G17, G18, G19
○
○
○
○
○
G52～G59
○
○
Optional block skip
Manual absolute on
Rotary axis roll-over
Coordinate system setting
Automatic coordinate system setting
Workpiece coordinate system
Sequence number
Absolute/incremental programming
Decimal point programming/ pocket
calculator type decimal point
programming
Input unit 10 time multiply
Plane selection
Rotary axis designation
Max. programmable dimension
External memory and sub program
calling function
Feedrate override
Jog override
Override cancel
External deceleration
Parity check
Control in/out
Tape code
Label skip
Program input
1 cycle press
Setting for press start signal
Positioning & press off
Manual press
External motion function
Changeable nibbling mode 2 steps
Press start wait
Press start lock
Cutting feedrate clamp
Automatic acceleration/deceleration
Feed per minute
Tangential speed constant control
Changeable Rapid traverse rate/time
constant according to positioning
distance
Positioning time constant control
Changeable position loop gain
Rapid traverse override
Circular interpolation
Dwell
Exact stop
Linear interpolation
Normal direction control
Rapid traverse rate
Exact stop mode
Interpolation functions
G00 (Linear interpolation type positioning is possible)Positioning
Program number
Dwell in seconds
Circular interpolation plus max. 2 axes linear Helical interpolation
Input signal is 1 point
Skip
High-speed skip
Press function
Feed function
Reference position return
2 A-80943E/01
Contents Summary of 0i-PB Specifications Additional Manual
- Page 1TECHNICAL REPORT (MANUAL) ＮＯ．ＴＭＮ0３／048E Date June,02 2003 General Manager of CNC Laboratory Series 0i-PB Specifications １．Communicate this report to: O Your information only O GE Fanuc-A, GE Fanuc-E FANUC Robotics CINCINNATI MILACRON O Machine tool builder Sales agency End user ２．Summary for Sales D
- Page 2Specifications for Series 0i -PB 01 Edition ：Standard ●：Standard option ：Option ＊：Function included in another option －：Not available Note) Some combinations of these options are restricted. In case of CNC Display with Personal Computer function, using CNC Screen Display Function is a premise. 0i
- Page 30i Item Specifications PB Interpolation functions Positioning G00 (Linear interpolation type positioning is possible) ○ Exact stop mode G61 ○ Exact stop G09 ○ Linear interpolation ○ Circular interpolation Multi-quadrant is possible ○ Dwell Dwell in seconds ○ Helical interpolation Circular interpolat
- Page 40i Item Specifications PB G code system A/B ○ Pattern function ○ Nibbling G68, G69, M code ○ Pattern base point command G72 ○ Memory and call by A/B macro 5 ○ U/V/W macro ○ Multi-piece machining ○ Command for restarting multi-piece ○ machining Repositioning G75, M code ○ Bending compensation G38, G3
- Page 50i Item Specifications PB Actual cutting feedrate display ○ Directory display of floppy cassette ○ Directory display and punch for each ○ group Graphic function Display unit with graphic is required. ☆ Servo setting screen ○ Servo waveform display Display unit with graphic is required. ＊ Display of
- Page 60i Item Specifications PB Others NC ready, servo ready, automatic operation, automatic operation start lamp, feed hold, reset, NC Status output signal ○ alarm, distribution end, rewinding, inch input, cutting, inposition, thread cutting, tapping, etc. 9" monochrome CRT/MDI ● 7.2" monochrome LCD/MDI
- Page 7Software of personal computer part in case of the CNC system which is connected with personal computer via HSSB(High Speed Serial Bus) Items Specifications Remarks Operating system Windows® 2000 *4 Extended library FOCAS1 *7 CNC basic operation package Option CNC screen display function Option Softw
- Page 8(Note) *1 : There are some limitations in case of CNC Display with Personal Computer Function. *2 : Only for CNC Display with Personal Computer Function. *3 : The actual registrable value might changes according to the registered number of programs and the program si *4 : Intel, Pentium are register