1. Fanuc
  2. Concerning addition of the Changing Active Offset Value with Manual Move

Concerning addition of the Changing Active Offset Value with Manual Move Supplement to Manual Page 2

Supplement to Manual
FANUC Series 18i/180i/180is - MB OPERATOR’S MANUAL
FANUC Series 21i/210i/210is - MA OPERATOR’S MANUAL
FANUC Series 21i/210i - MB OPERATOR’S MANUAL
Concerning addition of the Changing Active Offset Value with Manual Move
1.Type of applied technical documents
Name
FANUC Series 18i/180i/180is - MB OPERATOR’S MANUAL
FANUC Series 21i/210i/210is - MA OPERATOR’S MANUAL
FANUC Series 21i/210i - MB OPERATOR’S MANUAL
Spec.No./Ed. B-63554EN/01, B-63094EN/02, B-63614EN/01
2.Summary of Change
Group Name/Outline
New, Add,
Correct,
Delete
Applicable
Date
Basic
Optional
Function
Addition of the Changing Active Offset Value with
Manual Move
Addition Immediately
Unit
Maintenance
Parts
Notice
Correction
Another
1/2
PAGEEDT.
DATE
DESIGN
DESCRIPTION
TITLE
No.
18i/180i/180is - MB
21i/210i – MA/MB OPERATOR’S MANUAL
Concerning addition of the Changing Active Offset Value
with Manual Move
B-63554EN/01-1, B-63094EN/02-7, B-63614EN/01-4
01 Feb.06 ’03 Newl
y
Re
g
istered
Previous page
Next page

Contents Summary of Concerning addition of the Changing Active Offset Value with Manual Move Supplement to Manual

  • Page 1TECHNICAL REPORT NO.TMN 03/011E Date : Feb.06.’03 General Manager of Software Development Center FANUC Series 16i/18i/160i/180i/160is/180is - MA OPERATOR’S MANUAL FANUC Series 16i/18i/160i/180i - MB OPERATOR’S MANUAL FANUC Series 18i/180i/180is - MB OPERATOR’S MANUAL FANUC Series 21i/210i/210is - MA
  • Page 2FANUC Series 18i/180i/180is - MB OPERATOR’S MANUAL FANUC Series 21i/210i/210is - MA OPERATOR’S MANUAL FANUC Series 21i/210i - MB OPERATOR’S MANUAL Concerning addition of the Changing Active Offset Value with Manual Move 1.Type of applied technical documents FANUC Series 18i/180i/180is - MB OPERATOR’
  • Page 3• Adding “FANUC Series 16i /18i /21i – MA / MB Changing Active Offset Value with Manual Move (A-78535E)” to this description (Attached papers) FANUC Series 16i /18i /21i – MA / MB Changing Active Offset Value with Manual Move (A-78535E) 18i/180i/180is - MB 21i/210i – MA/MB OPERATOR’S MANUAL TITLE Co
  • Page 4FANUC Series 16i /18i /21i – MA/MB Changing Active Offset Value with Manual Move Index 1. Outline ........................................................................................................................... 2 2. Explanation..............................................................
  • Page 51. Outline If you want to perform roughing or semi-finishing with a single tool, you may fine-adjust the tool length compensation or cutter compensation. Moreover, you may want to fine-adjust the setting of the workpiece origin offset that was already set up. This function can change the offset (suc
  • Page 6Example The compensation value set at Z-axis of the offset number 10 becomes 54.700 + (-2.583) = 52.117 mm under the following conditions: • Specified H code: H10 • Value set at Z-axis of the offset number 10: 54.700 mm • Amount of movement caused by manual feed along the Z-axis: -2.583 mm 2.4 Chang
  • Page 7Example Assume the following conditions: • Specified workpiece coordinate system: G56 • G56 workpiece origin offset (X-axis): 50.000 • G56 workpiece origin offset (Y-axis): -60.000 • G56 workpiece origin offset (Z-axis): 5.000 • G56 workpiece origin offset (C-axis): 180.000 • Amount of manual feed-b
  • Page 82.7 Presetting the relative position indicator Setting parameter APL (No. 3115#5) to 1 can preset the relative position indicator (counter) to 0 automatically when active offset change mode is selected. In this case, performing manual feed until the relative position indicator (counter) becomes 0 ca
  • Page 93. Signal Active offset change mode signal CHGAO [Classification] Input signal [Function] This signal selects the manual feed-based active offset change mode. [Operation] Setting this signal to "1" selects the manual feed-based active offset change mode. • Automatic operation is at pause or
  • Page 10Signal addresses • Parameter No.5040#2(MOP)=0 #7 #6 #5 #4 #3 #2 #1 #0 G0297 AOFS2 AOFS1 CHGAO #7 #6 #5 #4 #3 #2 #1 #0 F0297 MCHAO • Parameter No.5040#2(MOP)=1 #7 #6 #5 #4 #3 #2 #1 #0 G0203 AOFS2 AOFS1 CHGAO #7 #6 #5 #4 #3 #2 #1 #0 F0199 MCHAO The following timing chart shows how the input and signal
  • Page 114. Parameter #7 #6 #5 #4 #3 #2 #1 #0 3115 APL [ Input type ] Parameter input [ Data type ] Bit axis APL Specifies whether to preset the relative position indicator automatically when the manual feed-based active offset change mode is selected, as follows: 0: Do not preset. 1: Preset. This signal is
  • Page 12#7 #6 #5 #4 #3 #2 #1 #0 5041 AOF [ Input type ] Parameter input [ Data type ] Bit AOF When the manual feed-based active offset change mode is selected in a reset state or a cleared state, the tool compensation: 0: Can be changed 1: Cannot be changed However, even if “1” is set in parameter CLR(No.34
  • Page 13#7 #6 #5 #4 #3 #2 #1 #0 3409 CFH [ Input type ] Parameter input [ Data type ] Bit CFH When bit 6(CLR) of parameter No.3402 is 1, the reset button on the MDI panel, the external reset signal, the reset and rewind signal, or emergency stop will, 0: Clear F codes, H codes, D codes. 1: Not clear F codes