FS 16i/18i/21i/20i/160i/180i/210i/15i/150i/Power Mate i ,etc. Additional Manual Page 5
Additional Manual
TITLE
DRAW.
No.
4 / 4
Page
FANUC LTD
DESCRIPTIONDESIGNDATE
EDIT
Preventive measures against errors
of linear scale caused by noise
A-65434EN
4x1202DA : Axis which No.1023 is set to 12.
4x1402CA : Axis which No.1023 is set to 13.
4x1402DA : Axis which No.1023 is set to 14.
4x1602CA : Axis which No.1023 is set to 15.
4x1602DA : Axis which No.1023 is set to 16.
4x1802CA : Axis which No.1023 is set to 17.
4x1802DA : Axis which No.1023 is set to 18.
4x1A02CA : Axis which No.1023 is set to 19.
4x1A02DA : Axis which No.1023 is set to 20.
4x1C02CA : Axis which No.1023 is set to 21.
4x1C02DA : Axis which No.1023 is set to 22.
4x1E02CA : Axis which No.1023 is set to 23.
4x1E02DA : Axis which No.1023 is set to 24.
Separate detector side feedback interpolation counter is shown in following address.
1002CC : Axis which No.1023 is set to 1.
1002DC : Axis which No.1023 is set to 2.
1202CC : Axis which No.1023 is set to 3.
1202DC : Axis which No.1023 is set to 4.
1402CC : Axis which No.1023 is set to 5.
1402DC : Axis which No.1023 is set to 6.
1602CC : Axis which No.1023 is set to 7.
1602DC : Axis which No.1023 is set to 8.
4x1002CC : Axis which No.1023 is set to 9.
4x1002DC : Axis which No.1023 is set to 10.
4x1202CC : Axis which No.1023 is set to 11.
4x1202DC : Axis which No.1023 is set to 12.
4x1402CC : Axis which No.1023 is set to 13.
4x1402DC : Axis which No.1023 is set to 14.
4x1602CC : Axis which No.1023 is set to 15.
4x1602DC : Axis which No.1023 is set to 16.
4x1802CC : Axis which No.1023 is set to 17.
4x1802DC : Axis which No.1023 is set to 18.
4x1A02CC : Axis which No.1023 is set to 19.
4x1A02DC : Axis which No.1023 is set to 20.
4x1C02CC : Axis which No.1023 is set to 21.
4x1C02DC : Axis which No.1023 is set to 22.
4x1E02CC : Axis which No.1023 is set to 23.
4x1E02DC : Axis which No.1023 is set to 24.
A mark “x” in above address represents logical slot number of additional axis board.
Please confirm logical slot number in the system configuration screen.
Contents Summary of FS 16i/18i/21i/20i/160i/180i/210i/15i/150i/Power Mate i ,etc. Additional Manual
- Page 1TECHNICAL REPORT (MANUAL) No. TMN01/178E Date 2001 General Manager of Hardware Laboratory Preventive measures against errors of linear scale caused by noise Communicate this report to : O Your information O GE Fanuc-N, GE Fanuc-E FANUC Robotics CINCINNATI MILACRON O Machine tool builder Sales agency
- Page 2Preventive measures against errors of linear scale caused by noise 1. Outline In this material, several preventive measures against errors of linear scale caused by noise in the system of FANUC Series 16i/ 18i/ 21i/ 20i/ 160i/ 180i/ 210i/ 15i/ 150i/ Power Mate i ,etc. are shown. 2. Preventive measur
- Page 3SDU : SIGNAL GROUND A02B-0236-C203 M3 screw terminal or GROUNDING WIRE A02B-0236-C205 to GROUND Preventive measures against errors TITLE of linear scale caused by noise DRAW. No. A-65434EN EDIT DATE DESIGN DESCRIPTION FANUC LTD Page 2/4
- Page 43. Axis Vibration The error of linear scale may not cause alarm but cause axis vibration. If the servo software is following edition, the feedback interpolation counter can be used to investigate the influence of the noise. l 90A0/X,Y l 90A6/A or later l 90B0/D or later Note) feedback interpolation
- Page 54x1202DA : Axis which No.1023 is set to 12. 4x1402CA : Axis which No.1023 is set to 13. 4x1402DA : Axis which No.1023 is set to 14. 4x1602CA : Axis which No.1023 is set to 15. 4x1602DA : Axis which No.1023 is set to 16. 4x1802CA : Axis which No.1023 is set to 17. 4x1802DA : Axis which No.1023 is set