1. Fanuc
  2. Series 30i-MODEL A, Small-Hole Peck Drilling Cycle

Series 30i-MODEL A, Small-Hole Peck Drilling Cycle Additional Manual Page 8

Additional Manual
Design Ed.
Approve
Design
page
Title
Draw.
No.
6/16
Description
FANUC Series 30i-MODEL A
Small-Hole Peck Drilling Cycle
A-79414E
Feb. 23, 2004
Date
Date
When the cutting feedrate reaches the minimum rate, the spindle speed
is not changed. The spindle speed can be increased up to a value
corresponding to the maximum value of S analog data.
- Advance and retraction
Advancing and retraction of the tool are not executed in the same manner as
rapid-traverse positioning. Like cutting feed, the two operations are carried
out as interpolated operations. Note that the tool life management function
excludes advancing and retraction from the calculation of the tool life.
- Specifying addess I
The forward or backward traveling speed can be specified with address I in
the same format as address F, as shown below:
G83 I1000 ; (without decimal point)
G83 I1000. ; (with decimal point)
Both commands indicate a speed of 1000 mm/min.
Address I specified with G83 in the continuous-state mode continues to be
valid until G80 is specified or until a reset occurs.
Note
If address I is not specified and parqmeter No.5172 (for
backword) or No.5173 (for forword) is set to 0, the
forword or backword travel speed is same as the cutting
feedrate specified by F.
- Fuctions that can be specified
In this canned cycle mode, the following functions can be specified:
- Hole position on the X-axis, Y-axis, and additional axis
- Operation and branch by custom macro
- Subprogram (hole position group, etc.) calling
- Switching between absolute and incremental modes
- Coordinate system rotation
- Scaling (This command will not affect depth of cut Q or small
clearance d1.)
- Dry run
- Feed hold
- Single block
When single-block operation is enabled, drilling is stopped after each
retraction. Also, a single block stop is performed by setting parameter SBC
(No.5105 bit 0)
- Feedrate override
The feedrate override function works during cutting, retraction, and
advancing in the cycle.
Previous page
Next page

Contents Summary of Series 30i-MODEL A, Small-Hole Peck Drilling Cycle Additional Manual

  • Page 1TECHNICAL REPORT NO. TMN 04/020E Date :Mar .30, 2004 General Manager of Software Laboratory FANUC Series 30i-A Newly additional functions 1. Communicate this report to: Your information only GE Fanuc-N, GE Fanuc-E FANUC Robotics MILACRON Machine tool builder Sales agency End user 2. Summary for Sale
  • Page 2FANUC Series30i –A newly additional functions Drawing number Functions 1 A-79227E External Data Input 2 A-79226E One Touch Macro call 3 A-79196E Temporary absolute coordinate setting 4 A-79354E System alarm 5 A-79349E Touch Panel Control 6 A-79253E Distance coded linear scale interface 7 A-79364E Li
  • Page 3FANUC Series 30i-MODEL A Small-Hole Peck Drilling Cycle Specifications FANUC Series 30i-MODEL A Title Small-Hole Peck Drilling Cycle Draw. No. A-79414E Ed. Date Design Description page 1/16 Date Feb. 23, 2004 Design Approve
  • Page 41 Programming (M-type) FANUC Series 30i-MODEL A Title Small-Hole Peck Drilling Cycle Draw. No. A-79414E Ed. Date Design Description page 2/16 Date Feb. 23, 2004 Design Approve
  • Page 51.1 Small-Hole Peck Drilling Cycle An arbor with the overload torque detection function is used to retract the tool when the overload torque detection signal (skip signal) is detected during drilling. Drilling is resumed after the spindle speed and cutting feedrate are changed. These steps are repea
  • Page 6Explanations - Componet operations of the cycle * X- and Y-axis positioning * Positioning at point R along the Z–axis * Cutting along the Z-axis (first time, depth of cut Q, incremental) Retracting (bottom of hole → minimum clearance ∆, incremental) Retraction Repeated until ( bottom of hole+∆→ to p
  • Page 7Note When receiving overload torque detect signal while the tool is advancing, the tool will be retracted (clearance ∆ and to the point R), then advanced to the same target point as previous advancing. - Changing the drilling conditions In a single G83 cycle, drilling conditions are changed for each
  • Page 8When the cutting feedrate reaches the minimum rate, the spindle speed is not changed. The spindle speed can be increased up to a value corresponding to the maximum value of S analog data. - Advance and retraction Advancing and retraction of the tool are not executed in the same manner as rapid-trave
  • Page 9- Custom macro interface The number of retractions made during cutting and the number of retractions made in response to the overload signal received during cutting can be output to custom macro common variables (#100 to #149) specified in parameters No.5170 and No.5171. Parameters No.5170 and No.51
  • Page 102 Connection (M-type) FANUC Series 30i-MODEL A Title Small-Hole Peck Drilling Cycle Draw. No. A-79414E Ed. Date Design Description page 8/16 Date Feb. 23, 2004 Design Approve
  • Page 112.1 Small-Hole Peck Drilling Cycle General In peck drilling, the tool enters and retracts from hole based on an overload torque detection signal (skip signal) until the designed hole depth is reached. The spindle speed and cutting feedrate are changed on each entry of the hole. The cycle is realized
  • Page 12during the previous cutting operation and the case in which no skip signal was received during the previous cutting operation, respectively. Cutting feed rate = F × α (First time) α = 1.0 (Second and subsequent times) α = α × β ÷ 100 (where β is the rate of change for each drilling operation Skip du
  • Page 13Signals Overload torque signal SKIP#1, SKIP#2, SKIP#3 [Classification] Input signal [function] Retracts a tool if an overload torque occurs. [Operation] When this signal becomes "1", the control unit operates as follows: - Retracts the tool, and changes the spindle speed and
  • Page 14Parameters No. #7 #6 #5 #4 #3 #2 #1 #0 5160 NOL OLS [Input type] Parameter input [Data type] Bit path #1 OLS When an overload torque signal is received in a peck drilling cycle, the feed and spindle speed are 0: Not changed. 1: Changed. #2 NOL When the depth of cut is reached, the feed and spindle s
  • Page 15No. Data Percentage of the spindle speed to be changed when the tool is retracted 5165 without an overload torque signal received [Input type] Parameter input [Data type] Word path [Unit of Data] % [Valid data range] 1 to 255 This parameter sets the percentage of the spindle speed change during a pe
  • Page 16F1: Cutting feedrate to be changed F2: Changed cutting feedrate Set b2 as a percentage. Note If the set value is 0, the cutting feedrate will not be changed. No. Data Lower limit of the percentage of the cutting feedrate 5168 in a small-hole peck drilling cycle [Input type] Parameter input [Data typ
  • Page 17No. Data 5172 Speed of retraction to point R when no I address is defined [Input type] Parameter input [Data type] Real path [Unit of data] mm/min, inch/min (input unit) [Minimum unit of data] Depend on the increment system of the reference axis [Valid data range] Refer to the standard parameter set
  • Page 18Alarms and Messages - Diagnostic display 520 Total number of retract operations during cutting since G83 was issued Total number of retract operations due to reception of the overload torque 521 signal since G83 was issued Note The indications of No. 520 and 521 are cleared by G83 during small-hole