1. Fanuc
  2. Series 30i-MODEL A, One Touch Macro call

Series 30i-MODEL A, One Touch Macro call Additional Manual Page 1

Additional Manual
TECHNICAL REPORT NO. TMN 04/020E
Date :Mar .30, 2004
General Manager of
Software Laboratory
FANUC Series 30i-A Newly additional functions
1. Communicate this report to:
Your information only
GE Fanuc-N, GE Fanuc-E
FANUC Robotics
MILACRON
Machine tool builder
Sales agency
End user
2. Summary for Sales Documents
3. Notice
Applied software of FANUC Series 30i-A
G001/22(V) or later
G011/22(V) or later
G021/22(V) or later
4. Attached Document
Drawing No. refer to attached table
Copy :
FLB1 Manager (2 pages from cover)
FLB2 Manager (2 pages from cover)
FLB3 Manager (2 pages from cover)
Original section of issue
Vice
General
Manager
Manager Chief
Person in
Charge
No. FLB1-04/2218
Date Mar. 30, 2004
ADE
Previous page
Next page

Contents Summary of Series 30i-MODEL A, One Touch Macro call Additional Manual

  • Page 1TECHNICAL REPORT NO. TMN 04/020E Date :Mar .30, 2004 General Manager of Software Laboratory FANUC Series 30i-A Newly additional functions 1. Communicate this report to: Your information only GE Fanuc-N, GE Fanuc-E FANUC Robotics MILACRON Machine tool builder Sales agency End user 2. Summary for Sale
  • Page 2FANUC Series30i –A newly additional functions Drawing number Functions 1 A-79227E External Data Input 2 A-79226E One Touch Macro call 3 A-79196E Temporary absolute coordinate setting 4 A-79354E System alarm 5 A-79349E Touch Panel Control 6 A-79253E Distance coded linear scale interface 7 A-79364E Li
  • Page 3FANUC Series 30i-MODEL A One Touch Macro call Specifications FANUC Series 30i-MODEL A Title One Touch Macro call Draw A-79226E No. Ed. Date Design Description Page 1/10 Date Jan.09.’04 Design. Apprv.
  • Page 4One Touch Macro call This function enables the following three operations in pushing the switch installed in the machine only by the change in a minimum LADDER program. (1) Changes to MEM mode. (2) Execution of macro program registered in memory. (3) Return to the mode before macro program is execut
  • Page 5End of macro program (6) Please instruct M02 or M30 at the end of the macro program. Moreover, please input external reset signal (ERS) or reset&rewind signal (RRW) with M02 or M30 on the PMC side. The program which had been selected before the macro was executed is automatically selected by reset.
  • Page 6Least 32ms MCST (PMC→CNC) MCRQ (CNC→PMC) Mode notification MEM before macro execution signal(CNC→PMC) Mode Change process(PMC) MCFIN (PMC→CNC) Mode indefinite MEM before macro MCEXE (CNC→PMC) MCEXx (CNC→PMC) Program Execution (CNC) M30 or M02 (CNC→PMC) ERS or RRW (PMC→CNC) Interruption of sequence I
  • Page 7Under such a condition, when reset or emergency stop are input, the operation which is described in “Interruption by reset or emergency stop” is executed. Stop by alarm When the execution of macro program is stopped by alarm, the abnormal end signal (MCSP) is output. Under such a condition, when res
  • Page 8Notes (1) Even if the macro call is being executed, mode selection signal (MD1,MD2,MD4) is effective. Therefore, please change the LADDER program to disable the mode change when the macro call executing signal (MCEXE) is “1” when the inconvenience is caused if the mode change is done. (2) The macro
  • Page 9Signal Macro call start signal MCSTx [Classification] Input signal [Function] This signal starts the macro call sequence. When the standing fall of this signal is detected, CNC starts the corresponding macro program. O number of the program started by the MCST1 signal is specified
  • Page 10Abnormal end signal MCSP [Classification] Output signal [Function] This signal notifies the sequence of the macro call is terminated abnormally. [Output condition] This signal is set to "1" in the following case: - When the sequence is interrupted by reset or emergency stop or alarm. This
  • Page 11Parameter 6095 The number of programs used by the macro call function [Input type] Parameter input [Data type] Byte path [Valid data range] 0 to 16 Specify the number of programs used by the macro call function. For instance, when three is set, macro call start signal MCST1, MCST2, and MCST3 is vali
  • Page 12#2 MC1 MTB dedicated folder 1 "//CNC_MEM/MTB1/" of the initial folders is: 0: Set as a search folder. 1: Not set as a search folder. #3 SYS The system folder "//CNC_MEM/SYSTEM/" of the initial folders is: 0: Set as a search folder. 1: Not set as a search folder. Note The folders set as the search ta