FS 16i/160i-PB, FS 18i/180i-PB, Program Auto Restart Additional Manual Page 4
Additional Manual
3. Operation
1) CNC memorizes active executing data (the active program block pointer and the position, etc.) to
nonvolatile memory during the machining operation.
2) Stop program (e.g. by reset switch), or CNC power-off.
3) The reference point return for all the axes is operated after power-on.
(This operation is not necessary in case of CNC system with absolute pulse coder.)
4) Select resume position by Restart position select signal (RSRSEL<G248#7>).
5) When operator pushes the restart switch in MEM mode, PMC sets the Program auto restart signal
(RSTRT<G201#7>).
6) When the RSTRT signal is turned “0” after “1”, CNC turns the restart procedure executing signal
(RSTRTL<F199#6>) “1”.
7) CNC positions the workpiece to the restart position (Restart position return process).
8) CNC searches the restart program, and searches the restart position on this program by using
memorized data (Restart position search process). In case of resume from mode start position,
please refer to 2.2.2.
9) When this search process is complete, CNC becomes feed hold status, and turns the RSTRTL
signal “0” and the restart procedure completion signal (RSTRTE<F199#7>) “1”. In case of resume
from mode start position, signal RSRCUT is set to “0”.
10) When the cycle start signal is pushed, CNC sets signal RSTRTE to “0” and the program execution
is restarted from the restart position.
Edit Date
Desig
Contents
Title
of
Drawing
Drawing
No.
FS16i/18i/160i/180i-PB
Program Auto Restart
S
p
ecifications
A-78518E
Page
4 / 4
Recog
nition
Newly designed Miyajima
Matsu
moto
01.06.01 01
01.09.21 02
Matsu
moto
Revision for mark *2
Miyajima
Contents Summary of FS 16i/160i-PB, FS 18i/180i-PB, Program Auto Restart Additional Manual
- Page 1FANUC Series 16i/160i-PB FANUC Series 18i/180i-PB Program Auto Restart Specifications Title FS16i/18i/160i/180i-PB of Program Auto Restart Matsu 02 01.09.21 moto Miyajima Revision for mark *2 Drawing Specifications Matsu Drawing 01 01.06.01 moto Miyajima Newly designed No. A-78518E Edit Date Desig R
- Page 21. Outline This function is used for resuming the machining after interrupted (e.g. reset, power-off, etc.). This is optional function. 2. Specification There are two resume methods. One is a resume from interrupted block, and other is a resume from mode start position. These methods are selected by
- Page 32.2 Resume from mode start position CNC positions the workpiece to the mode start position where the interrupt occurs, and resumes the machining. Restart process is separated as the following two processes. 2.2.1 Restart position return process CNC positions the workpiece to the restart position in
- Page 43. Operation 1) CNC memorizes active executing data (the active program block pointer and the position, etc.) to nonvolatile memory during the machining operation. 2) Stop program (e.g. by reset switch), or CNC power-off. 3) The reference point return for all the axes is operated after power-on. (Th
- Page 5Cycle start RSRSEL RSTRT RSTRTL RSTRTE RSRCUT Move to Move by Axis motion Stop restart position Stop program command Restart Feed hold Machining Status Reset state position return Restart position search state resumed Fig.3 Timing chart of resume from interrupted block M code for mode start Cycle st
- Page 64. Parameter No. #7 #6 #5 #4 #3 #2 #1 #0 16960 RSRPT Data type : Bit type RSRPT Restart position of interrupted block is: 0 : interrupted position. 1 : head position that is the interrupted block. 16961 Minimum value of M code for mode start (mode 1) 16962 Maximum value of M code for mode start (mod
- Page 75. Signal Program auto restart signal RSTRT
- Page 8Program auto restart procedure executing signal RSTRTL
- Page 96. Alarm No. Message Contents 5258 FEED HOLD IN RESTART When the restart procedure is interrupted by feed hold, this alarm is occurred. 5259 INTERRUPTED POSITION NOT FOUND When the restart position cannot be searched, this alarm is occurred. (Complement) Alarm No.5258 : When this alarm occurs, the r