1. Fanuc
  2. FANUC Series 16i/18i/21i

FANUC Series 16i/18i/21i Additional Manual Page 16

Additional Manual
Page
Name
No.
FANUC Series 16i /18i /21i
–
TA/TB
Peck tapping cycle (G84 or G88)
Specifications
A-78549E
5 NOTES
(1) In the following cases the peck tapping cycle is not performed. Instead, ordinary tapping
cycle or rigid tapping cycle is performed.
• When Q is not specified.
• When Q0 is specified.
(2) When the F15 tape format is effective, when adding address Q to G84.2, the peck tapping
cycle by G84(the front tapping cycle) is performed
(3) The way of the rigid tapping command depends on the parameter setting. Therefore, a
concrete command way is not described in this specifications. Please refer to the rigid
tapping of the operator's manual and the connection manual (function) separately.
(4) Please refer about the explanation of the canned cycle for drilling, too.
6 REFERENCE
- FANUC Series 16i /18i - TA Operator's Manual (B-63004EN)
- FANUC Series 21i - TA Operator's Manual (B-63084EN)
- FANUC Series 16i /18i - TB Operator's Manual (B-63524EN)
- FANUC Series 21i - TB Operator's Manual (B-63604EN)
• Canned cycle for drilling
• Rigid tapping
- FANUC Series 16i /18i /21i - A Connection Manual (Function)
(B-63003EN-1)
- FANUC Series 16i /18i /21i - B Connection Manual (Function)
(B-63523EN-1)
• Rigid tapping
Ed.
Date
Contents
Draw u
p
2004.06.09
16/16
Apprv.
Desig.
Desi
g
n
T. Kurokawa
Previous page
Next page

Contents Summary of FANUC Series 16i/18i/21i Additional Manual

  • Page 1FANUC Series 16i /18i /21i – TA/TB Peck tapping cycle (G84 or G88) Specifications Table of Contents 1 GENERAL ·············································································································2 2 SPECIFICATION································································
  • Page 21 GENERAL When the deep hole cutting is executed by the tapping cycle or the rigid tapping cycle, the cutting may be difficult because that the chips gets entangled in tool or the cutting resistance increases. In this case, this function, such that the cutting is performed by moving from point R unt
  • Page 32 SPECIFICATION When the parameter PCT (No.5104#6) is set to 1, this function is available. By setting the parameter PCP (No.5200#5), the tapping cycle type (high-speed peak tapping cycle or peak tapping cycle) is selected. And set return value (at high-speed peak tapping cycle) or clearance (cuttin
  • Page 43 FORMAT 3.1 HIGH-SPEED PECK TAPPING CYCLE In case of the parameter PCP(No.5200#5)=0, if commanding G84/G88 as the tapping, the high-speed peck tapping cycle is performed. G84 X(U)_ C(H)_Z(W)_ R_ P_ Q_ F_ K_ M_ ; or G88 Z(W)_ C(H)_X(U)_ R_ P_ Q_ F_ K_ M_ ; X_ C_ or Z_ C_ : Hole position data Z_ or X
  • Page 5Explanations This cycle operates as follows. 1. The tool is moved to the hole position in rapid traverse. 2. M code for C-axis clamp is output. (Only when M code for C-axis clamp is commanded.) 3. The tool is moved to the point R level in rapid traverse. 4. Cutting only distance q (depth of cut for
  • Page 63.2 PECK TAPPING CYCLE In case of the parameter PCP(No.5200#5)=1, if commanding G84/G88 as the tapping, the peck tapping cycle is performed. G84 X(U)_ C(H)_Z(W)_ R_ P_ Q_ F_ K_ M_ ; or G88 Z(W)_ C(H)_X(U)_ R_ P_ Q_ F_ K_ M_ ; X_ C_ or Z_ C_ : Hole position data Z_ or X_ : The distance from point R t
  • Page 7Explanations This cycle operates as follows. 1. The tool is moved to the hole position in rapid traverse. 2. M code for C-axis clamp is output. (Only when M code for C-axis clamp is commanded.) 3. The tool is moved to the point R level in rapid traverse. 4. Cutting only distance q (depth of cut for
  • Page 8Cutting start distance Cutting start distance (d) is the value which is set to parameter (No.5213). Return speed to Point R Cutting speed to Cutting start point The speed of the return operation to Point R and the speed of the cutting feed to cutting start point are the same as the speed of the cutt
  • Page 93.3 HIGH-SPEED PECK RIGID TAPPING CYCLE In case of the parameter PCP(No.5200#5)=0, if commanding G84/G88 as the rigid tapping, the high-speed peck rigid tapping cycle is performed. (Refer to the operator's manual etc. for the way of the rigid tapping command.) G84 X(U)_ C(H)_Z(W)_ R_ P_ Q_ F_ K_ M_
  • Page 10Explanations This cycle operates as follows. 1. Spindle is stop. 2. The tool is moved to the hole position in rapid traverse. 3. M code for C-axis clamp is output. (Only When M code for C-axis clamp is commanded.) 4. The tool is moved to the point R level in rapid traverse. 5. Spindle rotates to CW
  • Page 113.4 PECK RIGID TAPPING CYCLE In case of the parameter PCP(No.5200#5)=1, if commanding G84/G88 as the rigid tapping, the peck rigid tapping cycle is performed. (Refer to the operator's manual etc. for the way of the rigid tapping command.) G84 X(U)_ C(H)_Z(W)_ R_ P_ Q_ F_ K_ M_ ; or G88 Z(W)_ C(H)_X(
  • Page 12Explanations This cycle operates as follows. 1. Spindle is stop. 2. The tool is moved to the hole position in rapid traverse. 3. M code for C-axis clamp is output. (Only When M code for C-axis clamp is commanded.) 4. The tool is moved to the point R in rapid traverse. 5. Spindle rotates to CW. And c
  • Page 13Cutting start distance Cutting start distance (d) is the value which is set to parameter (No.5213). Return speed to Point R Cutting speed to Cutting start point Like the movement from the bottom of hole (Point Z) to Point R (above 14.), the overriding (Max. 2000 % ) is available with the return spee
  • Page 144 PARAMETER #7 #6 #5 #4 #3 #2 #1 #0 05104 PCT [Data type] Bit #6 PCT Address Q command about tapping cycle (G84/G88) is 0: Not available 1: Available ( = Peck tapping cycle ) A peck tapping cycle is performed when setting this parameter and the depth of each cutting is commanded by using the address
  • Page 1505213 Return or clearance in peck tapping cycle [Data type] Word [Unit of data] Increment System IS-B IS-C IS-D Unit Millimeter input 0.001 0.001 0.001 mm Input input 0.0001 0.0001 0.0001 inch [Valid data range] 0 to 32767 This parameter sets the return or clearance in the peck tapping cycle. Set a
  • Page 165 NOTES (1) In the following cases the peck tapping cycle is not performed. Instead, ordinary tapping cycle or rigid tapping cycle is performed. • When Q is not specified. • When Q0 is specified. (2) When the F15 tape format is effective, when adding address Q to G84.2, the peck tapping cycle by G84