1. Fanuc
  2. FS 16i/18i/21i-TA/TB Direct Input of Offset Value Measured B for 2 spindle lathe

FS 16i/18i/21i-TA/TB Direct Input of Offset Value Measured B for 2 spindle lathe Additional Manual Page 2

Additional Manual
A-60156E
Edit
Apprv
ApprvApprv
Apprv.
..
.Desig
DesigDesig
Desig.
..
.
Sheet
Title
Draw
No.
Date
DateDate
Date
Design
DesignDesign
Design
Descri
p
tion
Descri
p
tionDescri
p
tion
Descri
p
tion
Date
DateDate
Date
FANUC Series 16
i
/18
i
/21
i
– TA/TB
Direct input of offset value measured B
for 2 spindle lathe
Jan.31.02
1/13
Contents
1. Outline.................................................................................................................................... 2
2. Touch Sensor ........................................................................................................................ 2
3. Setting of Tool Offset Value ..................................................................................................3
4. Setting of Z-axis Work Origin Offset (G54
∼
G59) .................................................................. 6
5. Signal ..................................................................................................................................... 8
6. Parameter ............................................................................................................................ 11
FANUC Series 16i /18i /21i
– TA/TB
Direct input of offset value measured B
for 2 spindle lathe
Previous page
Next page

Contents Summary of FS 16i/18i/21i-TA/TB Direct Input of Offset Value Measured B for 2 spindle lathe Additional Manual

  • Page 1TECHNICAL REPORT (MANUAL) No. TMN02/011E Date : Feb. 12, 2002 General Manager of Software Development Center FANUC Series 16i/18i/21i-TA/TB Direct input of offset value measured B for 2 spindle lathe 1. Communicate this report to: Your information only ○ GE Fanuc-N, GE Fanuc-E FANUC Robotics MILACRO
  • Page 2FANUC Series 16i /18i /21i – TA/TB Direct input of offset value measured B for 2 spindle lathe Contents 1. Outline.................................................................................................................................... 2 2. Touch Sensor ...................................
  • Page 31. Outline In 2 spindle lathe which has the back spindle, each spindle has the workpiece coordinate system for itself. By using this function, it is available to set automatically the tool offset and the Z-axis workpiece origin offset corresponding to each work coordinate system with the touch senso
  • Page 43. Setting of Tool Offset Value Determine a specific point on the machine tool as the measuring reference position. In advance, set the distance from this point to the measuring position (contact face of the touch sensor) as a reference value, using parameter No. 5015 to 5018 and No. 5056 to 5059. S
  • Page 5The tool offset number can be selected by the parameter No. 5005#5 (QNI) manually or automatically. •QNI=0 (Manual selection) Set the cursor to the desired tool compensation number by operating the MDI (such as page and cursor keys). •QNI=1 (Automatic selection) In the offset write mode, the cursor
  • Page 6• Basic Procedure to Set Tool Offset Value The tool offset value is automatically set to the tool offset memory by the following operation. The distance between the measured reference position, which is the tool nose position of the standard tool or the imaginary position , and the tool nose positio
  • Page 74. Setting of Z-axis Work Origin Offset (G54∼ ∼G59) In 2 spindle lathe which has the back spindle, each spindle has the workpiece coordinate system for itself. By assigning any G code from G54 to G59 for each workpiece coordinate system, this function set Z-axis work origin offset of them automatica
  • Page 8• Basic Procedure to Set Z-axis workpiece origin offset Value The Z-axis workpiece origin offset value is automatically set by the following operation. This has to be performed after measurement of the tool geometry offset value. (1) Select the spindle measuring the tool offset by the measured spind
  • Page 95. Signal Tool offset write mode select Signal GOQSM [Classification] Input signal [Function] The mode for writing tool compensation is selected. [Operation] When this signal is turned “1” in a manual operation mode, the mode for writing tool compensation is selected. The control unit then a
  • Page 10Tool offset number select signals OFN0∼ ∼OFN5 OFN6∼ ∼OFN9 [Classification] Input signal [Function] Selects the tool offset number. [Operation] When the mode for writing tool compensation is selected, the cursor is automatically positioned on the tool geometry compensation n
  • Page 11Measured spindle check signal 1 S1MES Measured spindle check signal 2 S2MES [Classification] Output signal [Function] The spindle under measurement is specified. [Output condition] These signals check which head is being measured in the tool offset write mode or the workpiece origi
  • Page 126. Parameter #7 #6 #5 #4 #3 #2 #1 #0 5005 QNI [Data type] type] Bit QNI In Direct input of offset value measured B or this function 0 Not automatically select the tool offset number 1:Automatically selects a tool offset number #7 #6 #5 #4 #3 #2 #1 #0 5051 WNI DSN [Data type] type] Bit DSN When this
  • Page 13Distance (X2P) between reference position and X axis + contact surface 5056 on the touch sensor 2 Distance (X2M) between reference position and X axis - contact surface 5057 on the touch sensor 2 Distance (Z2P) between reference position and Z axis + contact surface 5058 on the touch sensor 2 Distan
  • Page 145053 Bias for tool offset numbers for measured tool offset value setting [Data type] Byte [Unit of data] Number [Valid data range] 1 to maximum tool offset count When this function is used, this parameter allocates tool offset numbers for measured tool offset measurement values to spindle 1 and spin