1. Fanuc
  2. FANUC LASER C2000-MODEL E Level up type Descriptions

FANUC LASER C2000-MODEL E Level up type Descriptions Additional Manual Page 18

Additional Manual
TITLE
DRAW.NO.
17／
FANUC LASER C2000-MODEL E
A-81057E-002
A
PPR.
EDIT
DATE.
DESIG.
DESCRIPTION
DESIG.
CHECK
010207 MAEDA DRAW
CHECK
SHEET
22
5.5. Cooling Water
(1) Water specification
Cooling water with following specification should be used to avoid rust and blockage
by chalk deposition. When using ordinary tap water it is strongly recommended to
use an ion exchange unit to get deionized water.
pH
（25
°C）
6.0 to 8.0
El. conductivity
μS/cm（25
°C）
< 200
Standard Chloride Cl
-
(ppm) < 20
Sulfate ion SO
4
2-
(ppm) < 50
M-alkalinity CaCO
3
(ppm) < 50
Total hardness CaCO
3
(ppm) < 50
Iron Fe
(ppm) < 0.3
Reference Sulfur ion S
2-
(ppm) N.D.
Ammonium ion NH
4
(ppm) < 0.2
Silica Si0
2
(ppm) < 30
(2) Water additives
We recommend to use following additives to adjust the water quality in areas where the
water quality is very poor. For the cleaning of the cooling water circuit a chemical
cleaner should be used. In extremely cold areas an anti freezing agent has to be
applied.
・Corrosion inhibitor Contlime K-6000 （Mitsubishi Gas Chemical Company, Inc.）
Kurilex L-111 (Kurita Water Industries LTD.)
・Chemical cleaner Deslime （Mitsubishi Gas Chemical Company, Inc.）
Kuridine I-302 (Kurita Water Industries LTD.)
(3) The freeze proofing
In the cold district, we will recommend the frozen prevention function to make the pump
work when the temperature decreases to be applied. In addition, the water temperature
must not fall too much building the heater into the chiller in the very cold district. We will
recommend the chiller with built-in heater because it should adjust the water
temperature to 20℃ or more when the oscillator is started. Warm up function will start
automatically when the temperature in the oscillator is too low when starting.
Moreover, use the ethylene glycol by 30% or less in the density when you unavoidably
use antifreeze. Limit the use in four months of winter.
In addition, it might not cause corrosion when the different kind of anticorrosive is mixed,
and do not use antifreeze with the anticorrosive.
Previous page
Next page

Contents Summary of FANUC LASER C2000-MODEL E Level up type Descriptions Additional Manual

  • Page 1TECHNICAL REPORT ＮＯ．ＴＭL ／ Date. 21-September-2005 General Manager of Laser Laboratory FANUC LASER C2000-MODEL E Level up type Descriptions 1. Communicate this report to: ○ Your information only ○ GE Fanuc-N, GE Fanuc-E FANUC Robotics MILACRON ○ Machine tool builder Sales agency End user 2. Summary f
  • Page 2FANUC LASER- MODEL C2000-E Level up type Description TITLE FANUC LASER C2000-MODEL E DRAW.NO. A-81057E-002 02 050917 MAEDA added Level-up C2000-E SHEET EDIT DATE. DESIG. CHECK DESCRIPTION 1／ CHECK EGAWA APPR. EGAWA 22 DESIG. 010207 MAEDA DRAW
  • Page 3Table of Contents 1. Abstract···································································································· 3 2. Specification····························································································· 4 2.1. Basic Specification································
  • Page 41. Abstract Laser C2000-E has now been improved. This level up C2000-E achieved the improvement of the processing performance by the improvement design of oscillator design. The following performance has been improved for increasing the sale in the market of 2kW-3kW class that accounts for about 50%
  • Page 52. Specification 2.1. Basic Specification The FANUC LASER C2000-MODEL E is available as a standard version for Japan and the USA as well as a European version with CE marking. Both long and short optical path length types are available. See following specification for details. (Level up type) Items
  • Page 62.2. Comparison table of level up type and conventional type Item Conventional Level up type Remark Specification A04B-0813-B301 A04B-0813-B321 -B311 -B322 Rated Power 2000W ← Maximum Power 2000W 2500W Maximum Pulse Peak 2700W ← Freq less than500Hz Power Duty less than 50% Pulse Enhancement Availabl
  • Page 72.3. ＣＷ Output power Below diagram shows the output power characteristic of Level up type C2000-E and Conventional type. This performance data is only for reference and can not be guaranteed. 3000 Level up (Hi power mode) Level up (Fine mode) Conventional 2500 2000 Laser output power (W) 1500 1000 5
  • Page 82.4. Pulse waveform Below diagram shows the pulse characteristic of Level up type C2000-E. This performance data is only for reference and can not be guaranteed. 2.4.1. Hi power mode Pc=2700W, Fr=200Hz, Du=50% 3200W 2000W 1000W 0W 1ms/DIV 2.4.2. Fine mode Pc=2700W, Fr=200Hz, Du=50% 2800W 2000W 1000W
  • Page 92.5. Long term stability Below diagram shows the long-term power stability characteristics of Level up type C2000-E. This performance data is only for reference and can not be guaranteed. - Power stability of Level up type C2000-E - (2500W CW : with power feedback control) 3000 2500 Laser output pow
  • Page 102.6. Cooling water pressure drop Below diagram shows the cooling water pressure drop of Level up type C2000-E. This data is only for reference and can not be guaranteed. Pressure drop of Level up type C2000-E 3.5 3.0 Cooling water pressure drop ∆P(kgf/cm2) 2.5 2.0 1.5 1.0 0.5 Default setting 75l/min
  • Page 112.7. FDA, CE Marking In case of an export to the USA an FDA registration has to be made. FANUC LASER C series already obtained the necessary accession number. If necessary, please ask for this accession number. In case of an export to Europe EC mechanical safety and EC EMC certification is required.
  • Page 123. Improvements in Level-up Type In the level-up type C2000-E, the following items have been modified from the conventional type as improvement. (Detail specification may be changed due to further improvements) 3.1. Addition of Processing Mode Change Function Processing mode of level-up type C2000-E
  • Page 133.4. Modifications of Laser Gas Composition (CO2:He:N2 Volume Ratio) Conventional Type：5:40:55 (N2 Balance) → Level-up Type：5:60:35 (He Balance) Caution: If conventional gas composition is used, The alarm will be generated at the start of the electrical discharge. Detail specification of laser gas f
  • Page 143.6. Caution for Installation of Level-up Type Level-up type C2000-E uses parts mostly common to the conventional type, thus cautions are basically the same as the conventional type. However, the following points are different from the conventional type, and caution is requested at installation. CNC
  • Page 154. New Functions of the CNC 4.1. Processing Mode Change Function 4.1.1. Procedure to change of processing mode Processing mode can be changed by the following procedure 1) Press MDI key “OFF SET” several times and display the laser related screen. 2) Press soft key “SET”. 3) Press page key and displ
  • Page 165. Installation conditions 5.1. Environmental conditions Environmental conditions are the almost same as for other FANUC Ｃseries lasers. (1) Ambient temperature +5 to 35°C Note 1. At temperature over 30°C, please purge a dry air into the cabinet. (2) Temperature drift Max. 1.1°C/min (3) Humidity Les
  • Page 175.4. Chiller Unit In the laser oscillator cooling water is necessary for the cooling of the laser gas, optical parts, and power supply units. Following are the necessary specifications for the chiller unit. (1) Chiller capacity Please refer to specification on page 4. (2) Water temperature range Ple
  • Page 185.5. Cooling Water (1) Water specification Cooling water with following specification should be used to avoid rust and blockage by chalk deposition. When using ordinary tap water it is strongly recommended to use an ion exchange unit to get deionized water. pH （25°C） 6.0 to 8.0 El. conductivity μS/c
  • Page 195.6. Laser gas (1) Laser gas specification For Level up C2000-E, following gas specifications are required: ・Composition and accuracy: CO2= 5±0.25%、 He= 60±3.00%、 N2= 35±1.75% （He Balance） ・Water vapor (H2O): less than 5ppm ・Hydrocarbons（CnHm): less than 1ppm ・Gas purity: higher than 99.99% (2) Conn
  • Page 20(5) Cautions on connection of tubes When doing the connection please consider following items. Make the tube length as short as possible Make sure that no contamination gets into the circuit Make sure that the tube is not exposed to high temperature Make sure that stepping on the tube is not possibl
  • Page 216. Order Specifications Level-up type C2000-E uses the following order specifications. Please select basic options according to the destination region. For details, please refer to the order list (B-70271EN). [Basic] Item Specification Laser oscillator For Japan / USA A04B-0813-B321 For Europe A04B-
  • Page 227. Dimensions 7.1. Short optical path length type TITLE FANUC LASER C2000-MODEL E DRAW.NO. A-81057E-002 SHEET EDIT DATE. DESIG. CHECK DESCRIPTION 21／ CHECK APPR. 22 DESIG. 010207 MAEDA DRAW
  • Page 237.1. Long optical path length type TITLE FANUC LASER C2000-MODEL E DRAW.NO. A-81057E-002 SHEET EDIT DATE. DESIG. CHECK DESCRIPTION 22／ CHECK APPR. 22 DESIG. 010207 MAEDA DRAW