FANUC Series 16i/160i-LB Processing Mode Change Function Additional Manual Page 5
Additional Manual
08
If you change the processing mode when on the way of start-up sequence after
laser oscillator is in discharge start ready state(F221#1/ LRDY=1) and HVON
signal is turned on or when laser oscillator is in laser oscillation state(F221#6/
LSTR=1), laser sequence is restarted after returning to the state before
discharging automatically by CNC. The state of signal HVON must be kept
as ”1” at this time. Discharge start ready signal LRDY is not turned on because
laser sequence is restarted from just after discharge start ready state. The
changed processing mode isn’t available just after changing the setting. The
changed processing mode becomes available when laser sequence is restarted just
after the discharge start ready state automatically by CNC.
・ In case that laser alarm occurs during the processing mode change
In case that laser alarm happens during the processing mode change, laser gas
change function is interrupted. Automatic restart of laser sequence by CNC does
not work even if alarm is released. When laser sequence becomes PURGE or
LRDY state by laser alarm, turn on the signal RUN( G222#6) or signal HVON
after removing the causes of alarm and releasing the alarm display by reset.
Then, Laser oscillator is started by CNC according to the set mode.
・ Processing mode change during power calibration
In case of changing the processing mode during power calibration is being
executed, power calibration function is interrupted and laser sequence is
restarted automatically by CNC to change the processing mode. After that, power
calibration function is restarted according to changed processing mode.
・ Processing mode change during warm up function
Warm up function of laser oscillator warms up the laser oscillator by repeating
internal discharge. In case of changing the processing mode during warm up
function, the laser oscillator is started up in the same way as you change the
processing mode during power calibration.
・ Processing mode change during automatic aging function
In case of changing the processing mode during automatic aging function is being
executed, aging operation at that time is executed in processing mode before
changing. Next execution cycle of aging function is executed in processing mode
after changing. For example, if you change the processing mode when remaining
cycles of aging function is “6”, aging function that cycle time is “6” is executed in
processing mode before changing. Next aging cycle (remaining cycle is “5”) is
executed in changed processing mode after former aging cycle (remaining cycle is
“6”) is completed.
Ed.
Apprv.Design
Date
Design
Descri
p
tion
Date
FANUC Series 16i /160i –LB
Processing mode change function
A
－90107E
Sep.17,2005
H.Tokito
5
/
19
Title
Draw
No.
Sheet
07
06
05
04
03
02
Contents Summary of FANUC Series 16i/160i-LB Processing Mode Change Function Additional Manual
- Page 1FANUC Series 16i/160i – LB Processing Mode Change Function Specification - Contents - 1. OUTLINE ....................................................................................................................2 2. SPECIFICATION ....................................................................
- Page 21. Outline This document shows Processing Mode Change Function in detail. Processing mode change function can change two level of laser gas pressure and various parameters corresponding to the laser gas pressure to realize a suitable processing performance of FANUC LASER C series for the processing
- Page 3The parameters for Fine mode are newly added in automatic aging function as follows. Table 2 : Setting parameters for automatic aging function of each mode Setting Parameter Parameter （High power mode） （Fine mode） Laser power in normal calibration No.15320 No.29060 Oscillation freq. in normal calibr
- Page 4・ Change of processing mode Setting screen for processing mode change is displayed with under mentioned procedure. ① Push the MDI key “OFFSET” several times and select the laser setting screen. ② Push the soft key [SET]. ③ Push the page key and select setting screen for processing mode. This setting
- Page 5If you change the processing mode when on the way of start-up sequence after laser oscillator is in discharge start ready state(F221#1/ LRDY=1) and HVON signal is turned on or when laser oscillator is in laser oscillation state(F221#6/ LSTR=1), laser sequence is restarted after returning to the stat
- Page 6・ Processing mode change during beam output In the setting screen, processing mode can be changed even if during automatic operation or laser output by manual operation. But laser beam can’t be outputted at that time because laser oscillation is stopped and restarted automatically by CNC to change l
- Page 7setting. And displayed items of aging function are also changed in the aging function setting screen. In case of parameter No.15014#4(MAG)=1, all the pages of aging setting screen are displayed. At that time, the items displayed in page 2 and page 3 are changed to those for High power mode or for Fi
- Page 829020 Power calibration coefficient（Fine mode） [Data type] Word [Unit of data] [Valid data range] 0～32767 The coefficient is used to calibrate the specified power according to the actual power. This parameter is automatically specified during power calibration. 29022 Bias value（Fine mode） [[Data typ
- Page 929026 Value 0 when half of the discharge tubes are used（Fine mode） 29027 Value 1 when half of the discharge tubes are used（Fine mode） 29028 Value 2 when half of the discharge tubes are used（Fine mode） 29029 Value 3 when half of the discharge tubes are used（Fine mode） 29030 Value 4 when half of the d
- Page 10[[Data type] Word [Unit of data] V [Valid data range] 0～32767 Specify power setting 0 to 8 at the table intervals, in the indicated order, when half of the discharge tubes are used. For the standard setting, refer to the sheet attached to the laser oscillator. 29048 Upper limit on power（Fine mode） [
- Page 11If the value obtained by multiplying the specified peak power value by the power override value is greater than the value set in this parameter, the duty ratio is clamped at 50% (fixed value), and the specified peak power value is clamped at the value set in parameter No.29049. When 0 is specified,
- Page 12pressure reaches parameter No.29046 after HVON(G222#7)=1. Alarm No.4125 can’t be monitored if this parameter value is zero ・ Settings for automatic aging function （Fine mode） 29060 Laser power in normal calibration（Fine mode） [[Data type] Word [Unit of data] W [Valid data range] 0～7000 Set the power
- Page 1329063 Calibration time of normal calibration（Fine mode） [[Data type] Word [Unit of data] sec [Valid data range] 0～32767 Set the time specified for obtaining the power calibration coefficient. Note When manually performing the aging operation by changing the setting, set the same value in parameter N
- Page 1429066 Laser pwer in aging（Fine mode） [[Data type] Word [Unit of data] W [Valid data range] 0～7000 Set the power to be specified when aging is performed by the automatic aging function. 29067 Oscillation frequency in aging（Fine mode） [[Data type] Word [Unit of data] Hz [Valid data range] 5～2000 Set t
- Page 15oscillator containing no inverter is used in an area using a supply frequency of 50Hz.) Note The gas pressure may have been changed in the field. So, input the values obtained by subtracting 100 from the settings of parameter No.29023 and No.29024 in parameters No.29070 and No.29071. 29071 Gas press
- Page 164.Signal － Oscillator start signal RUN
- Page 17－ Discharge start ready signal LRDY
- Page 18－ Automatic aging function execution signal AGNG
- Page 195.Alarm Number Message Meaning The composition 4125 LASER GAS SPEC/MIX (mixture) of laser gas is not correct for set processing mode. 6.Remarks z This function is a basic function. z This function is available when prm29016#7(CCM)=1 z Fine mode can’t be set for the laser oscillator that can’t use pr