APPENDIX
A. SPINDLE PARAMETER TABLE
B–65160E/02
324
FS0 Internal
data
number
F–xxx
Classi-
fica-
tion
Application
Contents
Standard
initial
setting
data
FS16i
/16
FS15i
FS15
1st
Spindle
Internal
data
number
F–xxx
Classi-
fica-
tion
SUB
low
speed
SUB
high
speed
MAIN
low
speed
MAIN
high
speed
Contents
Standard
initial
setting
data
FS16i
/16
FS15i
2nd
Spindle
1st
Spindle
2nd
Spindle
6144#1 6324#1 3324#1 3544#1 3180#1 4180#1 0 170#9
6144#2 6324#2 3324#2 3544#2 3180#2 4180#2 0 Whether to use external
one–rotation signal
f f
A 170#10
6144#3 6324#3 3324#3 3544#3 3180#3 4180#3 0 Setting of external one–
rotation signal detection
edge
f f
A 170#11
6144#4 6324#4 3324#4 3544#4 3180#4 4180#4 0 Setup of MZ sensor
(built–in sensor with
built–in motor)
f f
A 170#12
6144#5 6324#5 3324#5 3544#5 3180#5 4180#5 0 170#13
6144#6 6324#6 3324#6 3544#6 3180#6 4180#6 0 170#14
6144#7 6324#7 3324#7 3544#7 3180#7 4180#7 0 170#15
6145#0 6325#0 3325#0 3545#0 3181#0 4181#0 0 170#0
6145#1 6325#1 3325#1 3545#1 3181#1 4181#1 0 170#1
6145#2 6325#2 3325#2 3545#2 3181#2 4181#2 0 170#2
6145#3 6325#3 3325#3 3545#3 3181#3 4181#3 0 170#3
6145#4 6325#4 3325#4 3545#4 3181#4 4181#4 0 170#4
6145#5 6325#5 3325#5 3545#5 3181#5 4181#5 0 170#5
6145#6 6325#6 3325#6 3545#6 3181#6 4181#6 0 170#6
6145#7 6325#7 3325#7 3545#7 3181#7 4181#7 0 170#7
6146#0 6326#0 3326#0 3546#0 3182#0 4182#0 0 171#8
6146#1 6326#1 3326#1 3546#1 3182#1 4182#1 0 Setting of gear ratio
resolution
f f
B 171#9
6146#2 6326#2 3326#2 3546#2 3182#2 4182#2 0 Setting in 10min
–1
units
f f
C 171#10
6146#3 6326#3 3326#3 3546#3 3182#3 4182#3 0 171#11
6146#4 6326#4 3326#4 3546#4 3182#4 4182#4 0 171#12
6146#5 6326#5 3326#5 3546#5 3182#5 4182#5 0 Setting of analog over-
ride range
f f
B 171#13
6146#6 6326#6 3326#6 3546#6 3182#6 4182#6 0 171#14
6146#7 6326#7 3326#7 3546#7 3182#7 4182#7 0 Setup of rigid tapping
with MZ sensor (built–in
sensor with built–in mo-
tor)
f f
B 171#15
6147#0 6327#0 3327#0 3547#0 3183#0 4183#0 0 171#0
6147#1 6327#1 3327#1 3547#1 3183#1 4183#1 0 171#1
6147#2 6327#2 3327#2 3547#2 3183#2 4183#2 0 171#2
6147#3 6327#3 3327#3 3547#3 3183#3 4183#3 0 171#3
6147#4 6327#4 3327#4 3547#4 3183#4 4183#4 0 171#4
6147#5 6327#5 3327#5 3547#5 3183#5 4183#5 0 Whether to detect dis-
connection of position
coder signal
f f
D 171#5
6147#6 6327#6 3327#6 3547#6 3183#6 4183#6 0 Whether to detect
alarms (AL–41, 42, and
47) related to position
coder signal
f f
D 171#6
6147#7 6327#7 3327#7 3547#7 3183#7 4183#7 0 Setting of motor voltage
pattern at no load
f f
C 171#7
6148#0 6328#0 3328#0 3548#0 3184#0 4184#0 Depends
on the
model
Setup of electromotive
force compensation
(high–speed winding)
f
C 172#8
6148#1 6328#1 3328#1 3548#1 3184#1 4184#1 Depends
on the
model
Setup of electromotive
force compensation
(low–speed winding)
f
C 172#9
6148#2 6328#2 3328#2 3548#2 3184#2 4184#2 0 172#10
6148#3 6328#3 3328#3 3548#3 3184#3 4184#3 0 172#11