APPENDIX
B. LIST OF SPINDLE PARAMETER
NUMBERS
B–65160E/02
348
1st spindle
Contents
2nd spindle
Spindle switching
MAIN side
Contents
Spindle switching
SUB side
Spindle switching
MAIN side
Spindle switching
SUB side
High
–speed
charac-
teristics
Contents
Low
–speed
charac-
teristics
High
–speed
charac-
teristics
Low
–speed
charac-
teristics
High
–speed
charac-
teristics
Low
–speed
charac-
teristics
High
–speed
charac-
teristics
Low
–speed
charac-
teristics
3060 ² 3362 ² 3200 ² 3582 ² Position gain during orientation (HIGH)
3061 ² 3201 ² Position gain during orientation (MEDIUM
HIGH)
3062 ² 3202 ² Position gain during orientation (MEDIUM
LOW)
3063 ² 3363 ² 3203 ² 3583 ² Position gain during orientation (LOW)
3064 ² 3364 ² 3204 ² 3584 ² Rate of change in position gain upon
completion of orientation
3065 ² 3365 ² 3205 ² 3585 ² Position gain in servo mode/during syn-
chronization control (HIGH)
3066 ² 3206 ² Position gain in servo mode/during syn-
chronization control (MEDIUM HIGH)
3067 ² 3207 ² Position gain in servo mode/during syn-
chronization control (MEDIUM LOW)
3068 ² 3366 ² 3208 ² 3586 ² Position gain in servo mode/during syn-
chronization control (LOW)
3069 ² 3209 ² Position gain in Cs contour control mode
(HIGH)
3070 ² 3210 ² Position gain in Cs contour control mode
(MEDIUM HIGH)
3071 ² 3211 ² Position gain in Cs contour control mode
(MEDIUM LOW)
3072 ² 3212 ² Position gain in Cs contour control mode
(LOW)
3073 ² 3367 ² 3213 ² 3587 ² Grid shift in servo mode
3074 ² 3214 ² Reference position return speed in Cs
contour control/servo mode
3075 ² 3370 ² 3215 ² 3590 ² Detection level for orientation completion
signal
3076 ² 3371 ² 3216 ² 3591 ² Motor speed limit during orientation
3077 ² 3372 ² 3217 ² 3592 ² Orientation stop position shift
3078 ² 3373 ² 3218 ² 3593 ² MS signal constant
3079 ² 3374 ² 3219 ² 3594 ² MS signal gain adjustment
3080 3310 3375 3451 3220 3530 3595 3671 Conventional : Regenerative power limit
HRV : Regenerative power limit for high–
speed zone/regenerative power limit
3081 ² 3376 ² 3221 ² 3596 ² Delay time until motor power is cut off
3082 ² 3377 ² 3222 ² 3597 ² Setting of acceleration/deceleration time
3083 3280 3380 3428 3223 3500 3600 3648 Motor voltage during normal rotation
3084 ² 3381 ² 3224 ² 3601 ² Motor voltage during orientation
3085 3281 3382 3429 3225 3501 3602 3649 Motor voltage in servo mode/during syn-
chronization control
3086 ² 3226 ² Motor voltage in Cs contour control mode
3087 ² ² ² 3227 ² ² ² Overspeed level